Whirlpool Switch

This triple infinite surface element switch regulates power to a 3-size radiant burner on your cooktop. It lets you choose the small, medium, or large ring and adjust heat smoothly, restoring precise size selection and temperature control.

• Directs power to the inner, middle, and outer rings of a triple radiant surface element
• Cycles power to provide variable heat at the selected size
• Safe symptoms: burner won't change sizes or only one ring heats
• Safe symptoms: temperature stuck on high/low, won't turn off, or no heat

• Disconnect power before servicing
• Remove the knob/panel as needed; photograph wiring and transfer wires one at a time to matching terminals
• Secure the switch to the control panel, align the shaft, and reinstall the knob/panel
• Restore power and test all three element sizes across several heat settings

This auto load sensing water level pressure switch monitors the tub's water level via the air hose and signals the control to start or stop filling. It helps prevent underfilling or overfilling for consistent wash performance. What it does:

• Senses tub water level through air pressure and communicates with the control/timer
• Regulates automatic load-size fill by cycling the inlet valve circuit
• Addresses symptoms such as won't fill, won't stop filling/overfills, underfills, or cycle not advancing due to water-level detection issues

• One load-sensing water level pressure switch

• Disconnect power and shut off water supply before servicing
• Access the console/top to release and remove the switch
• Transfer wire connectors and the pressure hose one at a time; ensure the hose is seated fully and not cracked, kinked, or obstructed
• Do not adjust any calibration screws; mount in the same orientation and reassemble

The Water Level Switch is an OEM part for Whirlpool washers. It is responsible for monitoring and controlling the water level during the wash cycle, ensuring the appropriate amount of water is used for each load.

A bad water level switch can occur due to electrical issues, component failure, or physical damage. If you notice problems such as incorrect water levels, overflowing, or insufficient water in your washer, it may indicate a problem with the water level switch.

Symptoms of a bad water level switch include:

• Incorrect water levels, either too high or too low
• Washer overflows or fails to fill with water
• Insufficient water for proper cleaning or rinsing

Replace your faulty water level switch with this genuine OEM part to restore your washer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This broken belt switch monitors drive belt tension and cuts power to the motor if the belt snaps or slips. Replacing a faulty switch restores proper start/run operation and maintains the dryer's built-in safety shutoff. What it does:

• Monitors belt tension through the idler mechanism
• Opens the motor circuit if the belt is broken or loses tension
• Helps prevent the motor from running when the drum isn't turning
• Failure symptoms include: dryer won't start, stops soon after pressing Start, or no motor sound while controls have power

• Includes 1 broken belt switch

• Disconnect power; turn off gas supply for gas models
• Access the switch near the belt/idler area; many models require removing the front panel and drum
• Note wire locations; move connectors to the new switch and secure in the original orientation
• Inspect belt and idler for wear; ensure correct belt routing/tension before reassembly

This water level pressure switch senses tub water level and signals the control to stop filling and advance the cycle. Replacing a failed switch restores proper fill shut-off and allows the washer to move to wash, drain, and spin.

• Detects water level via air pressure in the attached hose from the tub air dome
• Signals the timer/control to close inlet valves at the selected fill level
• Enables agitation and spin only when the level is appropriate or the tub is empty
• Typical symptoms of a failed switch include overfilling or underfilling, continuous filling, cycle not advancing, or no spin

• Disconnect power and turn off water supply before servicing
• Access the switch in the control console or top panel; note wire locations for reassembly
• Transfer the pressure hose and wire connectors to the new switch one at a time; ensure the hose is clear, not kinked or cracked, and fits snugly
• After installation, run a quick fill test to ensure proper shut-off and cycle progression

This rotary encoder mounts behind the washer's cycle knob and tells the main control which setting you select. When it fails, selections may be erratic or unresponsive. Replacing it restores accurate, dependable cycle selection. What it does

• Detects the position of the cycle selector knob
• Sends selection signals to the main control board
• Enables precise cycle and option changes
• Common symptoms: knob turns but lights don't follow, random/incorrect selection, can't select a cycle, won't start

• One rotary encoder

• Disconnect power to the washer before servicing
• Access the control console and remove the knob/dial to reach the encoder
• Note orientation, unplug the harness, release tabs/screws, and swap in the new encoder
• Handle electronics carefully and avoid static discharge; verify knob-to-light tracking before reassembly

This push-button door switch senses when your refrigerator door opens and closes to control the interior light. Replace a worn or stuck switch to restore reliable lighting and proper on/off operation when the door moves. What it does:

• Turns the interior light on when the door opens and off when it closes
• Common fix for a light that won't turn on with the door open
• Resolves lights that stay on continuously with the door closed
• Addresses intermittent lighting from a sticking or damaged plunger

• One door switch

• Disconnect power to the refrigerator before servicing
• Carefully pry the old switch from the liner; protect the surface to avoid damage
• Transfer wires to the new switch one at a time to maintain correct connections
• Press the new switch fully into place and restore power to test operation

This limit switch monitors a set condition and opens or closes its contacts when that limit is reached. Replacing a failed switch restores proper safety cutoff and consistent operation of the appliance's heating or movement system. What it does:

• Senses a limit condition at its mounting point (such as temperature or travel/position, depending on model)
• Changes state at a defined threshold to protect components and wiring
• Interrupts power to heat or motor circuits, or signals a control to respond
• Common failure signs: no heat or shuts down early, runs continuously, won't start, or intermittent operation

• 1 limit switch

• Disconnect power to the appliance before servicing
• Note wire positions; transfer connectors one at a time or take a photo for reference
• Reinstall in the original orientation so the actuator or sensing surface contacts the correct area
• Address root causes (blocked airflow, binding mechanisms, shorted components) to prevent repeat failures

Color: Black

This replacement switch restores reliable on/off signaling to the circuit it controls, helping your appliance start, stop, and respond correctly. A worn switch can cause intermittent operation, no response, or lights and functions that don't activate. What it does:

• Provides an electrical open/closed signal to enable functions like starting a cycle, powering a motor or light, or shutting a feature off
• Acts as a safety/position interlock (such as door, lid, float, or hood) depending on the model
• Typical symptoms include won't start, won't stop, light won't turn on/off, or intermittent operation
• Can be checked with a multimeter for continuity when actuated

• 1 switch

• Disconnect power before servicing; turn off gas or water supply if applicable
• Access the switch, note wire locations, and transfer leads one at a time to the new switch
• Mount securely, ensure the actuator aligns and wires aren't pinched
• Reassemble and test operation before finalizing

This slide-style electrical switch selects or turns a function on and off inside the appliance. Replacing a worn switch restores reliable control when settings won't engage, respond intermittently, or the slider feels loose or broken. What it does

• Provides sliding on/off or multi-position selection for a specific feature
• Routes power to the associated component when a position is selected
• Helps restore proper response when a control becomes intermittent or unresponsive
• Common signs: slider sticks, feels loose, breaks, or shows heat discoloration on terminals

• 1 slide switch

• Disconnect power to the appliance before service
• Access the control panel; note wire locations and take a clear photo
• Move wires to the new switch one at a time; fully seat each connector
• Reassemble, restore power, and test each switch position

This miniature door switch is the snap-action interlock that tells the appliance when the door is closed. Replacing a worn or sticking switch restores reliable start/stop and proper door-status sensing for safe, consistent operation. What it does:

• Acts as the latch/interlock sensor for door open/closed status
• Signals the control to allow or prevent operation based on door position
• Typical symptoms include: won't start or shows a door message, stops when the door is bumped, or light/fan behavior doesn't match door position

• 1 miniature door switch

• Disconnect power before servicing. If working on a microwave, high voltage may be present even when unplugged—properly discharge the capacitor.
• Access the latch/interlock area; note wire positions and transfer one lead at a time to the new switch.
• Use a multimeter to confirm the switch changes continuity when pressed before reassembly.

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

This surface burner infinite switch controls power to an electric range or cooktop element, letting you set precise heat levels. Replacing a failed switch restores consistent heating and ensures the burner shuts off at the Off position.

• Regulates power to the surface element by cycling on and off for variable heat settings
• Interfaces with the control knob to adjust temperature from low to high
• Helps ensure the burner turns fully off at the Off position
• Common fix for a surface element that won't heat, only heats on High, won't shut off, or has erratic temperatures

• Disconnect power to the appliance before servicing
• Access the control panel, remove the knob, and unmount the old switch
• Move wires to the same labeled terminals on the new switch; transfer one at a time or use a photo for reference
• Secure the switch, reinstall the panel/knob, restore power, and test burner operation

This rotary switch controls settings by turning the appliance's control knob. Replace it to restore precise on/off and selection when the dial stops responding, only works in one position, or functions intermittently.

• Provides rotary input to select operating settings
• Changes electrical contacts at defined positions to signal the control
• Helps resolve issues like no response, single-setting only, or intermittent operation when turning the knob
• Matches original mounting and terminal layout for proper function

What's included: 1 rotary switch Install notes:

• Disconnect power at the breaker or unplug before servicing
• Remove the control knob and open the control panel to access the switch
• Label or photograph wire positions; transfer wires one at a time to the new switch
• Mount securely without bending terminals, reassemble, and test operation

This dryer temperature selector switch lets you choose between four heat settings for proper fabric care. Replacing a worn switch restores accurate temperature selection so loads dry evenly without overdrying delicate items.

• Controls the dryer's heat level across four selectable settings
• Faulty switch can cause incorrect temperatures or only one setting to work
• May lead to poor drying performance or fabric damage if not functioning
• Restores reliable temperature selection and consistent drying results

• Unplug dryer before servicing; shut off gas if applicable
• Pull control knob straight off to access the switch
• Transfer wires one at a time to the new switch to maintain correct positions
• Ensure switch shaft and flat align with the knob during reassembly