Admiral Parts

• Too hot

The heating element had a break in the heater coils, so I replaced it with a new one from Appliance Parts Pros. I also replaced the thermal fusible link and thermostat switch because they were so cheap it just made sense to go ahead and do it while I was in there. I also cleaned every nook & cranny in the dryer, then cleaned out the vent piping- which was about 100% clogged. The video's of how to tear down a dryer were indispensable to this repair - along with APP's always having the right... Read more

• Fridge too warm
• Noisy

I determined that the motor that drives the damper valve that allows cold air into the refer was noisy. I ordered the replacement part from AppliancePartsPro.com. It arrived within 3 days and I changed the units out, which took about 10 minutes total. All is quiet with the refer now. Read more

I started with the suspension pad kit and the tub suspension pads. I do have to say if you have an older model washer (mine is approx 17 years old) be prepared to let the inner tub sit in penetrating oil for a few days before attempting to take the tub out. I was able to get to this point on my own and then it wouldn't budge. My husband ended up buying some direct drive tool (it was pretty cool) and was able to break the tub free after two days. Yay! From there he took the the inner tub and put... Read more

Ordered part, the correct part came the next day. Read more

• Freezer not defrosting
• Fridge too warm

Toughest part of this repair is figuring out how to get things apart. Amana doesn't provide you a repair manual showing how to disengage the various plastic covers. Initially disassembled the bottom freezer compartment so I could get to the evaporator coils; they were completely frozen in block of ice, restricting air flow to the fridge above. Obviously, the auto defrost cycle had not been running, or was short-cycling. Manually defrosted. Found this link for running diagnostic tests on the... Read more

• Door latch failure

After finding the model number for my dishwasher, I looked on line for the part and ordered it. The part arrived next day. I was a little hesitant to tackle it myself, as I am a 67 year old female. However I decided I could do it and was all set until I found out that I needed a Torx screwdriver. This however was not going to stop me. At a trip to my neighbor I was able to find bit for a drill that would let me remove one screw. The next stop was to my favorite hardware store where I... Read more

Dishes were 'gritty' with an almost invisible coating of specks smaller than grains of salt. Prior to ordering parts, I had to determine which part(s) needed replaced and which could benefit from a good cleaning. After viewing Appliance Parts Pros YouTube Videos, I removed the Main Manifold (snaps right off) including the Top Spray Arm. I discovered the Flappers of the Docking Station (AP6009888) were worn out and/or missing. I removed the Docking Station simply by popping the old one off... Read more

An appliance repair man in area did repairs, the screws were not easy to find and none were supplied with baffles! Read more

Installed new pump Read more

I ordered parts from appliance parts pro at 3:30 on Friday and they were delivered at bout noon on Saturday the next day. Took the machine apart removed the old pads. With the directions in the packages put it back together and the wife ran 5 loads of clothes through it. Works great. Was awesome to get the parts so quick Read more

• Little to no heat when baking

The bake (bottom burner) worked after replacing the ignitor. Becareful and do not drop the ignitor or the element will break. I found out the hard way. I bought the first ignitor at a local appliance store. After breaking that one, I found another at appliancepartspros.com for $20 cheaper. Thanks appliancepartspros!!! Read more

Rebalanced the load but noticed the drum was sitting lower and the springs were wore out and it went out of balance easy, so i got the suspension rod kit and installed it and it works much better. It took me 2 hours because i didnt have adequate room to move around. Hour job if you have room. Read more

I ordered a new motor with a very helpful Chris.It arrived a day later with instructions and was easy to exchange with the old one.I am delighted with how it works and the price was good and the service excellent.thank you. Read more

I removed the front panel of the dryer and the metal cover over the blower wheel. Removed the lock ring and clamp. Removed the old wheel and placed the new wheel on the shaft. I thoroughly cleaned all the lint around the area and inside the front cover. I resealed the metal cover over the blower and reinstalled the front cover. Dryer works great. Easy fix, I spent more time thoroughly cleaning all the lint. Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more