Bumper, Bushing, Grommet Parts

This cam plate is the stamped metal guide that secures and locates the dryer drum, helping maintain smooth rotation and proper alignment. Replaces a worn or damaged cam that can cause noise, rubbing, or uneven drum movement. What it does:

• Positions and guides the dryer drum to prevent lateral movement and maintain alignment.
• Absorbs and transfers load between the drum and the rear support assembly for stable rotation.
• Reduces metal-on-metal contact that can cause squeaks, scraping, or worn drum edges.
• Helps restore smooth drum tracking when a broken or worn cam causes rubbing or off-center rotation.

• One cam plate

• Disconnect power before starting any repair to prevent shock or injury.
• Access typically requires removing the dryer front or top panel and supporting the drum; follow OEM service manual steps.
• Inspect associated rollers, glides, and mounting hardware and replace if worn to prevent repeat failure.
• Tighten fasteners to OEM torque and verify proper drum rotation before full reassembly.

Rubber grommet cushion for laundry center washers. Isolates vibration and prevents wear where components pass through openings. Replaces worn or missing.

Rubber grommet cushions wiring, tubes, or panels in your dryer. Replace if cracked, worn, or missing to prevent chafing and reduce vibration noise.

This rubber door bumper cushions and aligns the appliance door to prevent slamming and reduce vibration, helping doors close smoothly and protecting cabinet and door finishes from wear. What it does:

• Acts as a cushion between the door and cabinet, absorbing impact during closing
• Helps keep the door aligned and reduces rattling or vibration during use
• Prevents metal-to-metal contact that can cause chipping, scratching, or noise
• Commonly replaced when worn, flattened, cracked, or missing

• One rubber door bumper

• Remove power to the appliance before accessing the door area or hinges
• Usually presses into a hole or snaps into a mount on the door or cabinet; no special tools required for many models
• Inspect surrounding mounting boss for damage; replace if cracked or deformed

This cam timer is the mechanical control that sequences an appliance's cycles, restoring correct timing and function when the control knob stops advancing. Replace a worn or stuck timer to recover proper cycle progression and operation. What it does:

• Advances cycle stages by rotating cams that open and close control contacts
• Sends timed signals to motors, switches and circuits to start and stop functions
• Common symptom: cycles won't advance or unit stays stuck in one cycle
• Common symptom: timer won't turn or control knob feels loose/slips

• One replacement cam timer assembly

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control console or rear panel; use proper tools
• Note original timer position and knob alignment before removal for correct reassembly
• Test appliance through a full cycle after installation to ensure proper operation

This front baffle grommet cushions and secures a dryer's front baffle to reduce vibration and noise while helping keep the baffle properly positioned during operation. Fits select Whirlpool-built dryers. What it does:

• Cushions the baffle to reduce rattling, knocking or squeaking noises during spin
• Holds the baffle in place to prevent movement or rubbing against the drum
• Helps maintain even drum rotation and prevents premature wear of plastic/metal parts
• Can wear or crack with age, causing noise or loose baffle symptoms

• High-level replacement — remove dryer front or access panel;
• Use proper tools and support panels; keep screws and fasteners organized for reassembly
• Disconnect power (and gas if applicable) before starting work

Thin shim that aligns and levels your freezer door at the hinge point. Replace when worn, damaged, or missing to eliminate rubbing and uneven gaps.

Rubber grommet that cushions and secures your range door handle. Replaces worn, cracked, or missing grommets to restore snug fit and quiet operation.

Plastic standoff that secures and spaces the control board from the chassis. Replace if broken, missing, or worn to restore proper board mounting and insulation.

Mounting spacer shim for ranges and ovens. Positions components for proper alignment and stable operation. Replace if worn, missing, or damaged.

Secures and elevates the main control board to prevent electrical shorts. Replace if broken, cracked, or missing to restore proper board clearance.

Grommet link assembly cushions and secures moving refrigerator components. Replace if cracked, worn, or missing to restore proper fit and reduce vibration.

Threaded spacer for wall oven door handles. Installs between handle and door to maintain proper spacing. Replace if cracked, stripped, or missing.

Rubber stop bumper that prevents refrigerator rollers from over-extending. Replace if cracked, worn, or missing to stabilize appliance movement.

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

Upper spring tub sleeve for washers. This bushing cushions the suspension spring connection to the tub. Replace if worn, cracked, or missing.