Cooktop Heating Element

This large surface element restores consistent heat to a cooktop burner on electric ranges and cooktops. Replace a failed element to bring back reliable heating performance when a burner no longer warms or heats unevenly.

• Supplies heat to a single surface cooking zone
• Common fix for a burner that won't heat or heats intermittently
• Can address uneven temperatures or hot spots on that burner
• Replace if the element is visibly damaged or fails a continuity test

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the unit to cool completely; access method varies by model
• Note/photograph wire positions and transfer them to the new element
• Ensure the element sits flat and centered; test all burner settings after reassembly

This upper broil element sits at the top of the oven cavity to provide intense radiant heat for broiling and finishing. Replacing a burned-out element can restore top-heat performance and consistent, even results.

• Provides direct, high heat from the top during Broil to sear and brown food
• Common symptoms include: no broil heat, uneven top browning, only the bake element heats, visible cracks/blisters, or tripping a breaker from a shorted element
• Works with the oven control to cycle heat and maintain broil temperature
• A failed element typically shows no continuity when tested with a multimeter

• Disconnect power at the circuit breaker and allow the oven to cool completely
• Remove racks; support the element, remove mounting screws, and carefully pull it forward
• Transfer wires one at a time with insulated pliers; prevent leads from slipping back into the insulation
• Avoid bending the element or over-tightening screws; ensure terminals are fully seated, restore power, and test Broil

This radiant surface element mounts beneath the glass cooktop to heat a surface burner. Replace it when a burner won't heat or heats intermittently to restore normal, consistent cooking performance.

• Generates radiant heat under the glass-ceramic top for a surface burner
• Cycles on and off to help maintain the set temperature
• Typical failure signs: no heat, intermittent heat, or visible damage to the element/terminals
• Used on electric ranges and glass cooktops

• Disconnect power at the breaker and allow the cooktop to cool fully before service
• Lift/hinge the glass top and support it to avoid stress or cracks
• Note wire positions; transfer any mounting clips/brackets from the old element to the new
• Ensure the element sits level under the glass and all connections are secure before reassembly

This dual surface element restores steady, selectable heat to a cooking zone on your electric range or cooktop. It provides two heating areas in one burner position so you can match heat output to small or larger cookware.

• Heats cookware by energizing the inner ring alone or both inner and outer rings together
• Helps resolve issues such as a surface burner not heating, only one ring heating, or intermittent/uneven heat
• Replaces a cracked, blistered, or visibly damaged element to restore reliable performance

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element from beneath the cooktop; photograph wire locations for reference
• Carefully transfer any brackets, clips, or attached limiter from the original element if required
• Avoid touching the element surface; secure all connections and test both inner and dual settings after reassembly

This replacement bake element restores the lower oven heat in electric ranges/ovens. It brings back proper preheating and even baking performance when the original element is burned out or physically damaged. What it does:

• Provides the primary heat from the bottom of the oven during Bake cycles
• Common signs of failure: no heat in Bake, very long preheat times, uneven baking, or visible blisters/cracks on the element
• If Broil still works but Bake does not, the bake element is a likely failure point
• Located at the bottom of the oven cavity to deliver even, consistent heat

• 1 bake element

• Disconnect power at the breaker and let the oven cool completely before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward
• Transfer the two wires to the new element, keeping them from slipping back into the oven cavity
• Reinstall the element and screws, restore power, and test Bake

• With power disconnected, check the element for continuity; an open circuit typically indicates a failed element

The Range Dual Radiant Heating Element is designed to provide reliable and efficient heating for your Samsung range. Crafted as a genuine OEM part, this heating element ensures seamless compatibility and optimal performance with your appliance. Featuring a dual radiant design, it delivers consistent and even heat distribution, allowing you to cook your meals perfectly every time. The durable construction of the Range Dual Radiant Heating Element guarantees long-lasting use, reducing the need for frequent replacements and saving you time and money. Installation is straightforward, making it an ideal choice for DIY repairs without compromising on quality. By choosing this genuine OEM part, you can restore your rangeGÇÖs functionality with confidence, ensuring that your kitchen operates smoothly and efficiently. Enhance your cooking experience with a component that offers both reliability and superior performance, tailored specifically for Samsung ranges.

This electric surface element replaces a failed top burner on your range or cooktop. Installing a new element restores dependable, even heat and responsive temperature control when a burner won't heat or behaves inconsistently.

• Provides the heat for the selected cooking zone when the surface control sends power
• Common signs of failure: burner does not heat, heats intermittently or unevenly, visible burn spots/cracks, or an open reading on a continuity test
• A shorted element may trip the breaker or spark when that burner is turned on

• Disconnect power at the breaker or unplug the appliance before servicing; allow the cooktop to cool completely
• Access the element per your model's service manual; support any glass surface to avoid stress cracks
• Note wire positions and transfer connections one at a time; reuse original mounts and hardware
• Ensure the element sits level and secure before reassembly and testing

Restore dependable heat to your indoor grill module with this electric grill element. Replacing a worn or failed element brings back even cooking and consistent searing performance on compatible grill cartridges. What it does:

• Converts electrical power into radiant heat for indoor grilling
• Delivers even heat distribution across the grill area when functioning properly
• Common fix when the grill won't heat, heats slowly, or has cold spots
• Replace if the coil is cracked, blistered, or visibly damaged

• 1 electric grill heating element

• Disconnect power at the breaker or unplug the unit; allow all components to cool completely
• Remove grill grates and any shields or pans to access the element
• Lift the element straight up to disengage from the terminal block; avoid bending terminals and transfer any reusable clips/brackets if present
• Seat the new element fully in the terminals; verify secure connections before reassembly and testing

This dual radiant surface element sits beneath the glass cooktop and provides two heating zones to match your pan size. Replacing a failed element restores fast, even heating and proper control on the affected burner.

• Heats cookware via two concentric radiant circuits beneath the glass-ceramic surface
• Lets you select inner, outer, or both rings for small or large pans (via the burner control)
• Cycles with its internal limiter to maintain the temperature you set
• Common symptoms: no heat, only one ring heats, uneven or slow heating

• Disconnect power at the breaker before servicing
• Lift/remove the glass cooktop to access elements; support the glass to prevent stress or cracks
• Transfer wiring and any mounting brackets from the old element to the new one, moving one connection at a time and documenting positions
• Test the burner for proper operation before reassembly

Restore consistent bottom heat in your oven with this bake element. When the original element burns out, the oven may not heat, preheat slowly, or bake unevenly—replacing it restores dependable baking performance and even results. What it does:

• Supplies heat from the bottom of the oven during Bake cycles
• Helps the oven reach and maintain the set temperature
• Common symptoms of failure: little or no heat in Bake, slow preheating, uneven baking/browning
• Visible signs can include blisters, cracks, or breaks in the element

• 1 bake element

• Disconnect power at the breaker and allow the oven to cool before service
• Remove mounting screws and carefully pull the element forward to access the wires
• Transfer the two wires to the new element, keeping them from slipping back into the oven cavity
• Reinstall mounting screws, restore power, and test Bake operation

• A healthy bake element typically shows continuity on a multimeter; an open reading indicates it has failed.

This replacement heating element restores the heat your appliance needs to cook reliably. Swap in a fresh element to bring back consistent temperatures and dependable performance when the original has failed or become damaged.

• Converts electrical energy into heat for the appliance's cooking system
• Typical symptoms of a failed element: no heat, slow or uneven heating, visible blistering/cracks, or tripping the circuit breaker
• An open (no continuity) element will prevent the affected oven or surface zone from reaching set temperature
• Designed to fit specific models; match by model/part number for proper application

• Disconnect power at the breaker before servicing; elements run on high voltage
• Take a photo and move wires one at a time to the new element; ensure terminals are fully seated
• Handle the element carefully—do not bend, kink, or stress terminals
• Reuse existing mounting screws/brackets as applicable; verify no wires contact metal before restoring power

Replace a burned-out lower bake heating element to restore consistent heat and even baking. This part is the primary heat source during Bake cycles; when it fails, the oven may not heat, preheat slowly, or bake unevenly.

• Provides bottom heat for the oven during Bake cycles
• Common symptoms: no heat in bake mode, very long preheat, uneven or undercooked results, element not glowing
• Replaces elements with visible cracks, blisters, or breaks
• Restores consistent temperature recovery and even heating

• Disconnect power at the breaker and allow the oven to cool completely
• Remove racks; unfasten mounting screws; gently pull the element forward and move one wire at a time to the new element
• Prevent wires from slipping back into the insulation; support them as you work
• Do not overtighten screws or bend the element; restore power and test Bake

This 8-inch surface coil element restores a burned-out or damaged heating element on an electric cooktop. It delivers consistent 2100W heat for everyday boiling, frying, and simmering, so your range burners perform like new.

• Provides direct, even heat for pots and pans on coil-top ranges
• Common symptoms: surface element won't heat, heats unevenly, or cycles off prematurely
• Visual signs can include blisters, breaks, or hot spots on the coil
• Helps resolve issues caused by a failed element rather than the switch or receptacle

• Unplug range or switch off circuit breaker before servicing
• Allow the old element to cool completely before handling
• Pull the element straight out from the receptacle; align and push the new one fully into place
• Inspect the element receptacle for heat damage and replace if needed for best results

This part is the radiant heater intended for use on ranges. This part is also referred to as a surface element. It supplies the heat required to cook food. This particular radiant heater is the largest element on the cooktop. In the event that the burner is not heating up, this part may need to be replaced as there could be an element that is burned out. It may begin to heat up but won't get hot enough to cook correctly. The cook may also notice that the element does not cook evenly. There could also be physical signs of damage. Be sure to unplug the range prior to attempting to repair or replace this part.This particular radiant heater is compatible with appliances manufactured by the LG brand. It is sold individually. This part comes straight from the manufacturer.

This surface heating element restores reliable heat to an electric range or cooktop's top burner. Replace a failed or damaged element to bring back even, responsive heating for everyday cooking. What it does:

• Supplies heat to the selected surface burner when the control is turned on
• Can correct no-heat, weak or intermittent heat, or overheating due to internal failure
• Replaces elements with visible damage such as breaks, burn marks, or hot spots
• Helps restore consistent temperature control across the cooking zone

• 1 surface heating element

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element per your model; note wire locations and any brackets before removal
• Transfer wires and any retaining hardware to the new element in the same positions
• Avoid stressing the element or insulation; ensure it sits level and clear of glass/trim before reassembly

The broil element is the oven's upper heating element. It delivers intense radiant heat for broiling; replacing a failed element restores proper broil performance and more even browning.

• Provides top, direct radiant heat during the Broil cycle
• Symptoms of failure: no broil heat, uneven broiling, visible blistering/cracks or breaks in the element, sparking or tripping the breaker when Broil is selected
• Helps restore proper searing/finishing from the top of the oven

• Disconnect power at the breaker or unplug the range before servicing
• Remove oven racks; support the element while removing its mounting screws
• Gently pull the element forward and disconnect the two wires; prevent wires from slipping behind the oven liner
• Make firm, clean terminal connections; avoid bending the element, reinstall screws, then test the Broil cycle