Cooktop Parts

Your on line video pointed out the problem, how to test, and how to replace the element. I ordered the part it came the next day. Wife is very happy. Read more

Found the parts I needed ordered them from your site Received them and installed in a few minuets and was done Read more

• Oven not heating evenly

Ordered new screws and door gasket. Replaced the old door gasket now the oven warms up faster and bakes the stuff easier. Replaced the missing door trim screws. Now the door close without making noises. Read more

Replaced Oven control Board, I actually had a "professional" appliance repair man come to the house and tell me what was wrong with the oven. While he was standing in my kitchen, I noticed he pulled up the AppliancePartsPros.com website to quote me the pricing for the parts. I did not see it necessary to pay him the marked up price. He left the house without repairing the oven I proceeded to order the parts that same evening, replaced the bad parts the same day I received them. I noticed while... Read more

Swapped old with new. dead easy and fast delivery of part helped: good service, thank you . Read more

I ordered 7 new lens caps to replace them all. Took ten minutes to fix. Read more

Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site. Read more

After finding or oven no longer heated, we found that the clock/time (controller) board had failed and fused one lead of the wiring harness to the board. We replaced the board and entire wiring harness. Took about an hour to match the direct fit wiring harness and mount the new board. The job wasn't difficult just a little time consuming. Read more

I replaced the old burner with the new burner assembly which included the ignighter. The screw that held the old ignighter was frozen into the old burner such that just the ignighter could not be replaced. Be care full removing the screws to the burner as they also may be frozen and tend to snap off instead of unscrewing. You will need to drill an tap new holes. Read more

Would advise before doing this repair to watch the video for it. It is not a plug in connection anymore like older ovens. The key is to keep the connecting wires from the oven from falling or pulling into the inner wall of the oven. The wires may not come very far out away from the wall of the oven so make sure to secure them. The video shows a good way to do that. If you have an in wall oven this is very important because it would hard and time consuming to pull the oven out of the wall to... Read more

• Little to no heat when baking

Replaced ingniter. Unlike some of the repair videos I saw, I could do everything by removing the lower draw, and in fact access from the back of the stove was not an option on my Amana. Pulling the stove out and fussing around turned a likely ten minute job in to a twenty minute. Unit work great, now I just need to keep tabs on the broiler igniter, which may be on the way out as well. Read more

Turned stove breaker off in the main breaker box and also unplugged the oven from the 220 outlet. pulled the baking racks out of the oven and proceeded to locate the 1/4 screws just above the bake element where it passes through the metal wall and removed them. pulled the element forward until the wires were exposed and unplugged them and then attached the new element to the wires and reinstalled in reverse order. Read more

• Door won't close

Replaced the hinge and receiver. Read more

Bought new burner tops for all four burners. Lights great now with nice blue flames and no yellow. Read more

Unplugged the stove. Removed the back of the control panel. Removed and replaced the membrane keyboard and the main PCB. Reassembled the stove and everything was back to normal. The PCB was probably ok but I wanted to be sure and get the stove working as soon as possible so I replaced both parts at the same Read more

We replaced both front orifice holders. Very easy to bend and break. If it has a deep bend in it, It will slow down the gas flow to the burner. if you have a low gas flow your burner will burn low So check your small silver gas lines and if you smell gas check your lines Read more