Cooktop Switch

This fan relay is an electrical replacement part that restores the relay control for the refrigerator/freezer fan motor so the appliance can circulate air properly and maintain even cooling. Use it to replace a failed relay and return fan operation. What it does:

• Switches electrical power to the evaporator/condenser fan motor when the control calls for airflow
• Commonly used when the fan won't start, runs intermittently, or the appliance struggles to maintain temperature
• Helps stop clicking or repeated start attempts caused by a bad relay
• Works as the control interface between the main control and the fan motor

• One fan relay

• Always unplug the appliance before starting any repair to avoid shock risk
• Locate the relay on the compressor or control module per your model's service guide and note connector positions before removal
• Transfer wiring/plug connectors exactly; avoid bending pins or over-tightening fasteners

This fan switch restores dependable control of your appliance's ventilation fan. It routes power to the blower motor so you can turn the fan on and off from the control panel when the original switch becomes worn or fails.

• Controls electrical power to the blower motor
• Restores reliable on/off fan operation from the user interface
• Typical symptoms: fan won't start, won't shut off, runs intermittently, or the switch/rocker feels loose or broken
• Contacts can wear or arc over time from repeated use

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the switch from the control panel; note wire positions and take a photo for reference
• Move wires one at a time to the matching terminals on the new switch; replace any heat-damaged connectors
• Reassemble, restore power, and test fan operation

Exhaust fan won't turn off or stuck on? This rocker switch restores reliable blower control. Simple 5-minute fix—just disconnect wires and snap in new.

Burner not heating or stuck on? This infinite switch restores precise temperature control to your cooktop elements. Moderate DIY repair difficulty.

This is a variable resistance control that regulates the heat output of your cooktop's heating elements. It allows you to adjust cooking temperatures from low to high by controlling the electrical current to the elements. Replace it when burner heat levels can't be adjusted properly, elements stay on high heat, or temperature control becomes erratic.

If your electric cooktop burner won't heat properly or respond to knob settings, this infinite switch restores variable heat control from simmer to high.

Burner stuck on high or won't adjust temperature? This infinite switch restores variable heat control to electric cooktop surface burners. DIY repair.

Burner won't heat properly or stuck at one temperature? This infinite switch restores variable heat control to your cooktop elements. Direct replacement.

This rotary control switch replaces a worn or failed selector used to change cycles or settings on compatible appliances, restoring reliable user input and exact position selection. Easy-to-replace direct-fit control component. What it does:

• Sends a user-selected position to the appliance control so the unit runs the chosen cycle or setting.
• Replaces a cracked, loose, or non-responsive control shaft or knob interface.
• Stops intermittent or no-response issues when turning the control knob.
• Restores tactile click/position feedback for accurate selection.

• Disconnect power before service to avoid shock risk.
• Access may require removing the control panel.
• Handle the switch and control shaft carefully to avoid damaging terminals or alignment tabs.

Burner won't heat or stays on when turned off? This infinite switch controls surface element temperature. Moderate DIY repair with basic wiring knowledge.

This is a small micro-switch used in the grill module fan circuit of a range. It detects the position or state of the fan assembly and signals the control board to activate or deactivate the fan as needed. Replace this switch if the grill fan fails to turn on or off properly, or if the switch is visibly damaged or no longer clicks when actuated.

If your cooktop burners won't ignite or spark continuously, the igniter switch may need replacement. This part controls spark ignition timing.

This wire harness assembly routes power and signals between a range of appliance components to restore reliable electrical connections and proper component operation. Fits as a direct replacement harness used in compatible Whirlpool appliances. What it does:

• Carries power and control signals between control boards, motors, switches and sensors
• Replaces damaged, frayed or corroded wiring that can cause intermittent or failed component operation
• Restores reliable connector-to-connector connections and prevents shorts from exposed wiring
• Helps resolve issues such as intermittent operation, components that won't respond, or visible wiring damage

• Disconnect power to the appliance before starting any repair
• Take photos of the existing harness routing and connector positions to aid reassembly
• Ensure all connectors are fully seated and any retaining clips or straps are secured
• If wiring shows burn, melting, or damaged insulation, replace the harness rather than repairing temporary sections

Fix a cooktop that won't spark or light with this igniter switch harness assembly. Connects spark modules to burner igniters for reliable ignition.

Fix a burner that won't spark or ignite with this cooktop igniter switch. Stops continuous clicking and restores normal ignition. DIY repair in 1 hour.