Craftsman Parts

The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.

Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.

Symptoms of a bad float include:

• The dishwasher not filling or filling slowly
• Error codes related to fill issues
• Improper water levels impacting wash results

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Oven won't turn on or display is blank? This power control board supplies power to your range's electronic controls. Moderate DIY repair, 1-2 hours.

Side discharge chute for walk-behind mowers. Directs grass clippings away from mower deck. Replace if cracked, broken, or missing to prevent clogging.

Ground drive belt transfers engine power to the transmission and wheels. Replace if mower loses self-propel function or wheels stop turning. Verify fit with your model number.

Fix a refrigerator that won't cool or runs constantly. This temperature control thermostat cycles cooling based on compartment temperature. DIY fix in 15-20 min.

Controls gas supply pressure to burner manifold. Replace if regulator is cracked, sticking, or no longer maintaining correct pressure for consistent flames.

Replaces broken or sheared auger shear pin on snow throwers. This safety part snaps when auger hits obstacles to protect engine from damage.

Secures pins and shafts on lawn tractors and riding mowers. Replace if bent, missing, or worn. Bow-tie design inserts through pre-drilled holes.

Spindle assembly for lawn tractor mower decks. Connects blade to drive belt for cutting operation. Replace if cracked, worn, or damaged bearings.

This convection ring element supplies the heat for the oven's convection bake and roast cycles. Replacing a failed element restores even convection performance so foods cook properly across multiple racks.

• Provides the heat source for convection modes; the fan circulates air across this ring for uniform baking
• Common symptoms of failure: no heat in convection, very long preheat, or uneven results during convection cycles
• Visual clues include cracks, blistering, or burn-through on the element band
• Electrical clue: element tests open/infinite (OL) with a multimeter when power is disconnected

• Disconnect power at the breaker before servicing; this is a high-wattage circuit
• Access varies by model: remove the rear panel or the interior convection cover to reach the element and terminals
• Note wire locations and transfer leads to the new element one at a time
• Ensure the element sits flat and does not contact the cavity walls; tighten mounting screws snugly

Steering pinion gear connects the steering column to the front axle turning mechanism on riding mowers. Replace if worn, stripped, or damaged.

Complete fuel tank assembly for gas line trimmers. Includes molded tank, gas cap, primer leads, fuel lines with filter, and mounting screws. Replace cracked, leaking, or damaged fuel tanks.

Control cable that connects the auger handle to the engagement mechanism. Replace if cable is frayed, stretched, broken, or detached from the handle.

This thermostat is a temperature-sensitive switch that controls power to cooling components as temperatures change. Replacing a worn thermostat restores consistent cycling and more accurate temperature regulation, helping the appliance maintain stable performance. What it does:

• Senses temperature and opens/closes electrical contacts at set points
• Regulates operation of key cooling components to maintain target temperature
• Helps prevent overcooling, overheating, and erratic cycling
• Failure signs include: no cooling, overcooling, temperature swings, unit runs continuously, or short-cycling

• 1 thermostat

• Disconnect power before servicing; verify no voltage is present
• Access the thermostat location; label/photograph wire positions and transfer one at a time
• Install in the same position and orientation as the original to ensure proper thermal response
• Restore power and confirm proper cycling and temperature control

Grass catcher frame that holds the grass-catching bag on walk-behind mowers. Replace if bent, cracked, or broken. Bag sold separately.

Flange lock nut secures components on mowers and outdoor power equipment. Replace if stripped, corroded, or missing to restore proper fastening.