Door, Door Glass & Parts

The Rear Oven Door Glass is an OEM part for Whirlpool ovens. This glass panel is installed on the inside of the oven door and is essential for providing a heat-resistant viewing window, allowing users to monitor the cooking process without opening the door. Measuring about 20 inches by 10 inches, this quality glass keeps heat in the oven and provides a clear view for easy baking.

Symptoms of a bad Rear Oven Door Glass include:

• Cracks or chips in the glass,
• Visible streaks or fogging between glass layers that can't be cleaned,
• A loose fit that may cause heat to escape or the glass to rattle during oven use.

Causes of rear oven door glass damage typically include thermal stress from high heat, impact from closing the door too forcefully, or accidental bumps with pots or pans.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Inner Glass is an OEM replacement part for Whirlpool built-in and slide-in electric ranges. As an interior part, this tempered glass serves as the viewing window for the oven cavity below. It is precision cut by Whirlpool to fit seamlessly within the oven door frame assembly.

Causes of broken inner glass can include impact from heavy pots or pans dropped inside during loading/unloading. Thermal stresses from repeated heating cycles may develop fine hairline cracks as well. 

Symptoms of a cracked inner glass involve: 

• Visible lines or damaged areas that obstruct full viewing
• Potential safety hazards if glass fully separates from the doorframe
• Inability to efficiently view food inside without opening the door

Compatible with some KitchenAid and Jenn-Air built-in electric ranges too, replacing now prevents further door damage from glass shifting out of position over time. 

The Lid Switch Magnet is an OEM part for GE washing machines. This magnet interacts with the lid switch to signal that the washer lid is closed, allowing the washing cycle to begin.

Causes of a bad lid switch magnet can include wear and tear from frequent use, physical damage, or loss of magnetism over time. A malfunctioning magnet can prevent the washer from detecting a closed lid, thereby interrupting the wash cycle.

Symptoms of a bad Lid Switch Magnet include:

• Washer not starting or stopping mid-cycle
• Error codes indicating lid issues
• Washer not spinning or agitating
• Lid lock mechanism not engaging

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lid Assembly is an OEM part for GE washing machines. This part is the lid of the washer. It is essential for securely covering the washer drum, preventing water from splashing out during the wash cycle, and allowing safe operation by ensuring the washer does not run with the lid open.

Causes of a bad lid assembly can include general wear and tear, physical damage from heavy loads or impacts, or issues with the hinges or latch mechanisms.

Symptoms of a bad lid assembly include:

• Difficulty in opening or closing the lid
• Washer not starting or stopping mid-cycle due to a faulty lid switch
• Visible cracks or damage on the lid
• Water leaking from the top of the washer

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Panel is an OEM part for GE microwaves. It forms the outer layer of the microwave door, providing both aesthetic appeal and protection for the inner components. This is a white outer door panel for a microwave. For the black panel, order WB55X10813.

Causes of a bad door panel can include physical damage from impacts or accidents, exposure to high heat, or wear and tear over time. Cracks, dents, or discoloration can compromise the panel's integrity and affect the microwave's performance.

Symptoms of a bad door panel include:

• Visible cracks or dents
• Difficulty in opening or closing the door
• Poor sealing, leading to heat or steam escaping
• Changes in the microwave’s appearance or functionality

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Glass Oven Door Outer Trim is an OEM part for GE ranges. It provides a protective and decorative frame for the outer glass panel of the oven door. This trim helps to secure the glass in place while also contributing to the overall aesthetic of the appliance.

Causes of a bad outer trim can include wear and tear from regular use, accidental impacts that cause cracks or chips, or exposure to high temperatures that can lead to warping or discoloration.  

Symptoms of a bad Glass Oven Door Outer Trim include:

• Visible cracks or chips in the trim
• The trim becoming loose or detached from the door
• Discoloration or warping of the trim
• Difficulty in securely closing the oven door

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The GE Glass Oven Door is an OEM part for GE ranges. It allows for viewing of dishes inside the oven cavity without opening the door.

Symptoms of a bad glass oven door include:

• Cracks or chips in the glass surface reduce structural integrity  
• Inability to form a proper seal around the oven chamber when closed
• Leaks or drafts felt around the door seal during baking 

Causes of a bad glass oven door may include normal wear and tear over years of heating and cooling cycles. Exposure to cleaning chemicals could potentially erode seals prematurely as well.

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Outer Door Frame is an OEM part for Whirlpool microwaves. This component serves as the exterior frame of the microwave door, providing structural support and housing the inner glass and other components.

You should replace the outer door frame if it becomes damaged or worn out. Common causes of a bad outer door frame include physical impact, wear and tear from frequent use, or exposure to heat and steam over time.

Symptoms of a bad outer door frame include:

• Cracks or visible damage to the frame
• Difficulty in opening or closing the microwave door
• Gaps between the frame and the microwave door components
• Loose or misaligned door parts

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Inner plastic door film covers the holes in the inner door frame.

Replace a cracked or cloudy door window with this outer lens. It forms the transparent exterior panel of the door, protecting the inner window and restoring a clean look and clear view into the drum during cycles.

• Forms the exterior, see-through panel of the door window
• Shields the inner window and helps the door close evenly against its trim
• Replace if the outer window is cracked, chipped, warped, loose, or discolored/cloudy
• Damage may cause poor visibility or sharp edges around the door opening

• Disconnect power before servicing the appliance
• Remove the door and place it on a padded surface
• Separate inner/outer door panels, note screw locations, and lift out the old lens
• Clean mating surfaces; set the new lens in place and reassemble without over-tightening screws

This inner oven door glass panel replaces a cracked, shattered, or stained pane to restore a clear viewing window and a safe barrier in the door, helping your oven heat properly and look like new. What it does:

• Forms the interior layer of the oven door window assembly
• Helps contain heat in the cavity and supports proper temperature performance
• Restores clear visibility into the oven
• Common failure signs: visible cracks or chips, shattered glass, rattling fragments, or heat escaping at the door

• 1 inner door glass panel

• Disconnect power and allow the oven to cool completely; shut off gas supply if applicable
• Remove the door per the service/user manual and place it on a padded surface
• Wear cut-resistant gloves and eye protection; handle glass by the edges only
• Note the order and orientation of panes, spacers, and trim; transfer hardware and avoid over-tightening screws against glass

Color: Stainless

The Microwave Door is an OEM component specifically designed for Bosch microwaves. It provides a barrier that safely contains microwave energy within the cooking cavity. 

Causes of a bad microwave door can include wear and tear over time, exposure to continuous heat and steam from cooking, as well as accidental impacts that damage the sealing surfaces.

Symptoms of a bad microwave door include:

• Failure to securely latch or lock in place  
• Warping or cracks in the glass window inhibit visibility
• Loose door mounting prevents proper sealing
• Microwave energy leaks when the door is closed  

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Microwave Door is an essential component for maintaining the functionality and safety of your Samsung microwave. Crafted as a genuine OEM part, this door ensures a perfect fit and reliable performance for your appliance. Designed with durability in mind, it withstands daily use while providing a secure closure to prevent microwave energy from escaping. Replacing a damaged or worn-out door with this genuine OEM part restores your microwave to its original condition, enhancing both its appearance and efficiency. Compatible with a wide range of Samsung microwave models, the Microwave Door guarantees seamless integration and easy installation. By choosing this high-quality replacement part, you can confidently extend the life of your microwave and continue enjoying its convenient features without compromise. Invest in the Microwave Door to ensure your kitchen appliance operates safely and effectively, providing peace of mind and consistent performance for your everyday cooking needs.

This replacement oven door glass panel restores safety and visibility to your range or wall oven. Replace cracked or shattered glass to maintain the door's insulating barrier and a clear view of your cooking without replacing the entire door. What it does:

• Serves as one pane of the oven door window for viewing the oven cavity
• Helps maintain proper door integrity and heat containment when used with the other panes
• Replace if the original glass is cracked, chipped, shattered, or missing
• Can resolve cloudiness or staining isolated to a damaged pane

• One glass panel

• Disconnect power or turn off gas and allow the appliance to cool completely
• Wear cut-resistant gloves and eye protection; handle the new glass by the edges
• Remove the door and disassemble the door stack; retain and reuse existing trim and fasteners
• Clean out all glass fragments before reassembly and avoid overtightening hardware

This outer door panel replaces a damaged or scuffed microwave door exterior in the Graphite finish, restoring a clean look and proper fit of the door assembly so the handle mounts securely and the door opens and closes smoothly.

• Forms the visible exterior of the microwave door and supports the handle mounting points
• Helps maintain proper door alignment for smooth opening/closing and latch engagement
• Replaces panels that are cracked, warped, or heavily scratched/dented
• Common symptoms include a loose handle mount, rattling outer frame, or cosmetic damage

• Disconnect power at the breaker or unplug the appliance before servicing
• If over-the-range, support or remove the microwave to a stable work surface for safe door service
• Separate the door halves, transfer the handle/trim as required, and install the new outer panel
• Ensure the door closes flush before restoring power