Electrolux Control Board

This electronic control board manages the appliance's main functions and user interface, restoring proper control and timing so cycles run as commanded. Replace a failed board to regain responsive controls and correct operation. What it does:

• Receives input from the control panel and sends signals to motors, valves, and heaters
• Interprets sensor feedback to regulate cycle timing and temperatures
• Stops or prevents operation when control electronics fail, causing unresponsive buttons or no display
• Can cause incorrect or intermittent cycles, error codes, or loss of power to controlled components

• Disconnect power (unplug or shut off breaker) before starting any repair
• Ground yourself to avoid static damage; handle the board by its edges
• Transfer any harnesses, mounts, or shields from the old board to the new board exactly as installed

This electronic power board supplies and regulates the appliance's control electronics so cycles and user-interface functions run correctly. Replacing a faulty board restores reliable power distribution to the control system. What it does:

• Regulates and distributes power to the appliance's control circuitry and display
• Controls signals between user inputs and internal components
• Helps the appliance complete cycles and maintain proper operation
• Common symptom: appliance shows a blank or unresponsive display or will not power on
• Common symptom: intermittent operation, error codes, or failure to start functions

• One electronic power board

• Disconnect power to the appliance before beginning any repair
• Handle the board carefully; avoid static discharge and contact with circuit components
• Verify the part number matches your appliance before installation

This board-switch is the appliance control board that routes power and signals to selector switches, helping the unit respond when you change settings. It replaces a failed switch board so controls operate reliably again. What it does:

• Routes electrical signals between the user controls and the appliance's circuits
• Enables selector and control inputs to change cycles, temperatures, or functions
• Can resolve symptoms like unresponsive or intermittent control operation
• Works as the user-interface switching assembly when the original board fails

• One board-switch as shown

• Disconnect power before installation to avoid shock or damage
• Handle the board by the edges and avoid touching contacts or components
• Verify connector seating and wire routing against the original during reassembly

This electronic control is the main control board that manages cycle functions, timing and user inputs so your appliance runs the selected programs. It restores digital control when the original board fails. What it does:

• Controls and coordinates appliance cycles, timers and component relays.
• Interprets user inputs from the touchpad or knobs and sends commands to motors, valves and heaters.
• Common symptoms: unresponsive controls, no display or error codes, cycles that won't start or advance.
• Replaces a failed or intermittent control board that causes erratic operation.

• Disconnect power to the appliance before servicing to avoid shock hazard.
• Handle the board carefully; protect it from static and physical damage.
• Verify the part number on the existing board before ordering to ensure correct replacement.

This is a replacement oven control board from Frigidaire. The oven control board is responsible for controlling all aspects of oven operation and for carrying out user commands, such as setting timers, adjusting temperature, changing bake/cook cycles, and more. It also includes a digital display where the clock and timer are shown. As an electronic component, internal faults can develop over time.Symptoms of a failing control board include being unable to operate the oven, being unable to set a timer, incorrect or erratic operation, and more. Replacing the control board is relatively easy. The user will need to unplug the oven, and then pull it out from the wall. Remove the top access panel to reveal the back of the control board. Remove the mounting screws, disconnect the wires, and remove the old board. Install the new board.This genuine OEM part is sold individually. It is designed to fit Electrolux ovens.

This is the main electronic control board that manages an appliance's functions and user commands, restoring proper control when the original board fails. It replaces a failed control module to help return normal operation. What it does:

• Interprets inputs from buttons, dials, and sensors and sends signals to start cycles and actuators
• Controls timing, heating/cooling outputs and cycle sequencing for the appliance
• Common symptoms: unresponsive controls, no display or erratic behavior, cycles that won't start or complete
• Electronic part—faults can cause intermittent or complete loss of function

• Disconnect power to the appliance before starting; risk of electric shock
• Handle the board by the edges and avoid static discharge—use an anti-static strap if possible
• Removing trim or access panels and unplugging wire harnesses is usually required; keep track of fasteners

This electronic control board manages a refrigerator's core functions and user interface, restoring proper cycle control and responsive panel operation when the original board fails. What it does:

• Regulates compressor and defrost cycles to maintain correct cooling patterns
• Processes user inputs from the control panel and display
• Controls timed events like defrost and fan operation
• Faulty boards can cause unresponsive controls, incorrect temperatures, or erratic cycling

• Disconnect power before removing or installing the board to avoid shock or damage
• Handle the board by the edges and avoid static discharge; use an anti-static wrist strap if available
• Verify the board's part number against your unit before installation—some repairs require matching sub-models

This electronic power board supplies and regulates voltage to the appliance's control system, helping restore reliable startup and control functions. Replace a damaged board to address intermittent power, no display, or failure to start. What it does

• Regulates and distributes power to the appliance's control modules and user interface.
• Helps restore normal startup when the unit won't power on or shows a blank display.
• Can stop erratic cycling or intermittent operation caused by failed power regulation.
• Works with the control electronics to enable responsive button/display behavior.

• One electronic power board (control PCB)

• Disconnect power at the breaker or unplug the appliance before servicing.
• Handle the board by the edges and avoid static discharge; use antistatic precautions if available.
• Verify harness connections match and seating is secure before reassembly.

This electronic control board manages the appliance's user interface and internal functions, restoring proper cycle and display operation when the original board fails. Replace a faulty control board to regain reliable control and correct electronic behavior. What it does:

• Processes user inputs from the console and sends commands to components
• Regulates timed cycles, display indicators and electronic diagnostics
• Common symptom: appliance is unresponsive or buttons do not work
• Common symptom: display is blank, shows error codes, or cycles run incorrectly

• Disconnect power before starting; verify unit is completely de-energized
• Handle the board by its edges and avoid touching components to prevent ESD damage
• Compare the new board to the old one for connector and mounting match before installing