Electrolux Gasket & Seal

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

The blower housing seal is a perimeter gasket that closes the gap between the blower housing and the adjoining duct or bulkhead. It keeps airflow contained for efficient operation and helps prevent air leaks and debris from escaping.

• Seals the blower housing joint to minimize air leakage
• Helps maintain proper airflow for consistent performance
• Reduces dust/debris escape into the cabinet or surrounding area
• Replaces torn, brittle, flattened, or missing seals that can cause weak air output or rattling

• Disconnect power; turn off gas supply before servicing.
• Access the blower housing; note the original routing/orientation of the seal.
• Remove the old seal and clean mating surfaces of lint and residue.
• Seat the new seal evenly with no gaps or twists; reassemble and verify airflow.

This freezer door gasket forms the airtight seal between the freezer door and cabinet. Replacing a worn or damaged seal helps keep cold air in, reduce frost buildup, and restore proper temperatures and efficiency.

• Creates a tight perimeter seal to prevent warm air leaks and moisture intrusion
• Helps maintain stable freezer temperature and humidity
• Reduces frost and ice accumulation around the door area
• Common symptoms: visible gaps or tears, door not sealing fully, condensation at the door edge, heavy frost near the door

• Disconnect power before servicing
• Warm the new gasket (soak in warm water or use gentle, low heat) to relax and ease installation; do not overheat
• Remove the old gasket; seat the new gasket fully into the door channel (some models require loosening and retightening retainer screws)
• Verify an even seal all around; perform a paper/dollar-bill test and adjust corners as needed

This flexible door gasket replaces a worn refrigerator seal to help maintain a tight fridge/freezer seal and improve temperature stability. It restores proper door sealing to reduce energy loss and help prevent moisture buildup. What it does:

• Creates an airtight barrier between the door and cabinet to keep cold air in
• Helps reduce frost or ice buildup by limiting warm, moist air entry
• Prevents water pooling from condensation at the door edge
• Can eliminate drafts, noisy closing, or difficulty latching caused by a damaged seal

• One replacement door gasket

• Remove power to the appliance before starting and work with clean, dry hands
• Clean mounting surface and channel; gently warm the gasket if stiffness prevents seating
• Start at a corner and press the gasket evenly into the channel; check for full, continuous contact around the door

This genuine replacement door gasket seals the refrigerator door to keep cold air inside and help maintain temperature control. Replacing a worn gasket restores proper sealing to reduce frost, leaks, and energy loss. What it does:

• Forms an airtight seal around the refrigerator door to keep cold air in and warm air out
• Helps prevent frost buildup and interior condensation by maintaining a consistent temperature
• Reduces energy use and prevents food spoilage caused by poor door sealing
• Fits into the door channel and compresses to create a tight, reliable seal

• For safety, unplug the appliance before starting any repair.
• Remove the old gasket by loosening screws/clips and pulling the gasket from the door channel; follow OEM instructions.
• Warm the new gasket or use a hair dryer to make it more pliable for easier installation and a snug fit.
• After installation, check for gaps and allow gasket to form to the door; avoid sharp tools that could damage the seal.

This burner seal fits around a cooktop burner to help keep spills and debris out of the burner housing and provide a stable, centered burner location for consistent heating. It restores a flush seal between the burner and the cooktop surface. What it does:

• Forms a protective gasket around the burner to block food, grease and liquids from entering the cooktop cavity
• Cushions and centers the burner, reducing wobble and promoting even element-to-surface contact
• Helps reduce smoke or odors caused by spills burning on exposed internal surfaces
• Restores proper fit after a cracked, torn or missing seal

• One burner seal

• Disconnect power to the appliance before servicing; if the range is gas, shut off the gas supply
• Remove the burner or lift the cooktop per your model's service instructions to access the seal area
• Clean and dry the mounting surface thoroughly before installing the new seal
• Press the seal into place; do not stretch excessively or use solvents/adhesives unless your model's instructions specify

This door gasket seals the refrigerator door to help maintain proper temperature and reduce energy loss. It replaces a worn, torn, or compressed seal to improve cooling performance and food safety. What it does:

• Creates an airtight seal between the door and cabinet to keep cold air in and warm air out
• Helps prevent frost build-up and reduces moisture inside the compartment
• Can stop visible gaps that allow warm air and odors to enter
• Restores consistent temperatures for better food preservation

• One refrigerator door gasket

• Handle gently to avoid stretching or tearing; follow the appliance manufacturer's alignment and fastening steps
• Clean the door flange and gasket channel before installation for a proper seal
• Some gaskets require heating (hair dryer) or a short break-in period to fully seat; follow your model's instructions

This replacement door gasket seals the refrigerator compartment to keep cold air in and warm air out, helping maintain consistent temperatures and reduce energy use. It fits along the cabinet opening and forms the primary seal between door and cabinet. What it does:

• Creates an airtight seal to help maintain internal cooling and reduce compressor runtime
• Prevents warm, moist air from entering and causing frost build-up or condensation
• Helps keep food fresher by maintaining stable temperatures
• Common symptom: visible cracks, gaps, or torn edges around the door perimeter
• Common symptom: warm spots inside the fridge, excessive frost, or higher energy use

• Unplug or disconnect power to the appliance before starting any repair
• Remove the old gasket and clean the sealing surface thoroughly before installing the new gasket
• Some installations require basic hand tools; check the appliance's service guide for detailed steps
• If adhesive or clips are used, follow OEM instructions

This door gasket seals the refrigerator door to help maintain proper temperature and energy efficiency by preventing warm air from entering the cabinet. It replaces a worn or torn seal to restore a tight closing perimeter. What it does:

• Creates an airtight seal around the refrigerator door to help keep cold air in and warm air out.
• Helps reduce frost buildup and keeps food at consistent temperatures.
• Commonly replaces gaskets that are cracked, flattened, torn, or no longer form a tight seal.
• Can reduce excessive compressor run time and cycling caused by air leaks.

• One refrigerator door gasket.

• High-level DIY replacement: remove the old gasket, clean the door flange, and press the new gasket into the retainer channel; some gaskets may require slight heating to set the fit.
• Check alignment and ensure gasket fully seats around the door perimeter before testing.
• Use basic hand tools; disconnect power if working near electrical components or lighting.

This door gasket is the flexible seal that lines a refrigerator door to keep cold air in and warm air out, helping maintain temperature and reduce energy use. It replaces a worn or damaged seal to restore a consistent fridge environment. What it does:

• Creates an airtight seal around the refrigerator door to minimize cold-air loss
• Helps prevent frost build-up and reduces condensation inside the compartment
• Reduces compressor run time by improving temperature retention
• Common symptoms of a failing gasket: warm spots, visible gaps, water or frost buildup, or higher energy use

• One door gasket

• Disconnect power or unplug the appliance before starting any work
• Clean the door flange thoroughly before installing to ensure a proper seal
• Start installation at a corner, fit gasket evenly into the door channel, and work around the door to avoid twists
• If the gasket is stiff, warm it gently to help seat it; if fasteners or adhesive are present on the original part, reuse them as required