Electrolux Parts

• Fridge too warm

Fan motor went bad. Fixed the fridge for less than it would have cost me just to have someone come out and look at it. Read more

I believe we had two problems. Our gasket was ripped in several places and our drain pan line was clogged. Therefore the water was frozen and backing up into the freezer. Replacing the gasket is an easy job and could possibly be done quickly enough that you don’t have to remove your freezer food items if you don’t discover additional problems during the process. The most time-consuming part is the approximately 40 screws that hold the freezer door shelf panel and gasket to the door itself. ... Read more

I ordered the replacement part. Your website was the only one I searched which exactly identified the correct part for me to order. The exploded diagram with numbered parts was very helpful. Read more

I first felt along each heating element (bake and broil) hoping to find a rough or blistered place on them. But they were both smooth with no irregular places. (replacing the elements would have been the easiest and cheapest repair. Pulled the back off the range (unplugged, of course) - checked wiring. There were no loose connections or burned wiring. I disconnected the elements and checked them with a ohmmeter (VOM) and both had continuity. Discovered that both elements used the same... Read more

• Will not drain
• Noisy

So, Saturday, the washer wouldn't drain, yes, I tried the Drain/Spin cycle. So I took the clothes out, rinsed them out twice in the laundry sink and dried them. After a quick Google search, I came to the conclusion that the pump was bad and ordered a pump, $125. Over the course of the next four days, expecting the new pump on Thursday, I baled out the washer, pulled it out from the wall and propped up the front (it's HEAVY), removed the front access panel, removed the drain inlet and outlet... Read more

• Marks left on clothes
• Noisy

The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible. Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem. Next step was to... Read more

Ordered a new seal, and replaced it with a new one freezer works great now. Read more

If you can't pull out the displacement pins on the crisper cover support clips that allow the wall to carry the weight of the cover, slides and drawer, you may need to push those pins in (they fall down the wall) to remove the clip. During the replacement of both front clips, I had one I could remove and one I had attempted to drill a tiny hole in to be able to pull the pin. Ultimately it did not work and needed to be simply pushed in. Do not worry, there is nothing below which the plastic... Read more

• Spins slowly
• Burning smell
• Pumps but will not spin
• Will not agitate

I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more

My 12 year old Frigidaire stack on top dryer had been beeping distress messages in some unintelligible code for about a year when it completely stopped producing heat. It also had a long standing issue with delicate fabrics and thin straps or drawstrings getting caught in the drum. After using this site to troubleshoot and viewing the useful how-to videos, I ordered and replaced the heating element, thermal limiter, and felt seals. Based on others' stories, I decided to also replace the rear... Read more

I researched online and found that it was probably one of two things wrong: the heat probe or the control board (clock). Since the probe was less expensive, I ordered that on Appliance PartsPros. It arrived SO quickly, and with the repair video I easily replaced it. BUT... it still got the F10 reading. Sigh. So I found a local appliance repairman (I didn't want to replace a more expensive item if it turned out I was wrong). He was a good one: he listened to my story, said he was sure it was the... Read more

• Little to no heat when baking

With my tools Read more

• Won't start
• Element will not heat

My old White Westinghouse stove has easy replacement of the elements & drip pans. They literally pop in & out with no effort or education necessary. Read more

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

• Door won't open or close

Replaced the lower hinge bearing and lower door cam on fridge side. Read more