General Electric Refrigerator Parts

• Door won't open or close

The fix involved removing the two bolts holding the broken door stop and bolting in place the new stop. Unless you take the door off, you have to work by feel due to the position of the door stop and the bolts holding the stop in place. A little patience is all that's required. A flip lock designed to keep kids out of cupboards is now in place so the damage won't reoccur. But if it does, its a quick, easy and inexpensive fix. Read more

First I called the local retailer to ask about a non-warranty service. Minimum $100 charge. Figured I would take a shot at the repair as I had fixed the fridge once before. I used a digital thermometer to verify that the temperature in the ice maker compartment was at the right temperature. I put the ice maker in diagnostic mode to eject the ice that was sitting in the ice tray (turn off and on and then push the ice full lever three times). Ice was successfully ejected. Sometimes the ice... Read more

After one of the glass shelves in our fridge shattered, I thought it would be expensive and hard to find a replacement, but luckily I found it at a very inexpensive price on AppliancePartsPros.com! It arrived just a couple days later, and it was a perfect fit. If I ever need to replace another appliance part, I will definitely be using this service. Read more

I looked for a site that sold replacement parts for my make of GE refrigerator. I found AppliancePartsPros, and was very surprised at how organized it was. By entering the model number of my refrigerator, I was shown a set of (approximately) 8 general parts diagrams for my refrigerator. I chose the ice making/dispensing diagram. I matched the part that shattered (from use) to what was on the diagram. What I didn't know was how to install the part. I saw references by other customer comments to... Read more

Put in new one Read more

These gaskets (seals) are friction held in a groove and just pull out by hand. The new ones simply can be pushed back into the groove by using your fingers to go around and work them in. Pull a corner of the old one out and push it back in to see how the fit. The gaskets need warming and softening with a hair dryer to straighten after arrival for correct shape, better fit, workability, and to regain their shape, but this is a simple job. The only catch, is that the door flap has to be... Read more

Took the ice maker apart and replaced the auger. Used U-Tube video as reference. Read more

Good ole Maryland with its 70 degree weather one day and a snow storm the next! 55 mph winds do not have any sympathy with above-ground transformers in a snows storm. The transformer blew - partially... then kept popping causing multiple surges to our homes AND electronics. Power was restored several hours later, however my fridge was not working. After I checked it out, I could see the burnt parts on the PCB board itself. I grabbed the part number and ordered the replacement PCB. When it... Read more

Suspected a clogged condensation drain line. Took out all the shelves and drawers, condensation unit is toward the bottom of the frdige on inside, I could see that there was ice build up. I unplugged fridge, placed fan in firdge to speed up the thawing of the built up ice. After ice melted enough, I could get face panels and foam off to see that icing caused a backup in drain line, which led to water sitting in trough pan, rusting the trough pan. Rust then accumulated in the drain line,... Read more

• Noisy

I had found that the fan in the freezer was making a lot of noise. Turns out the shaft was loose, causing the flan blade to wobble. Replaced the motor and fan and now it runs like a new unit. Read more

After reviewing a number of testimonials and your videos from your APP.com site I determined my most likely problem was either the defrost heater, thermostat, timer or possibly all three. The real challenge now began. Getting to the specific parts with my specific model number was a real challenge. It was not as easy as removing the light guard and 5 screws since my model had two Track Cant Shelf vertical rails restricting the removal of the back panel. Also, these rails could not be removed... Read more

Ordered new parts Read more

Could not clean yellowed door handles. Knew re-paint would look cheap. Bought both GE factory handles with shipping for a very fair price and had them in 2 or 3 days during the Christmas rush. I will definitely buy from this company again. Read more

I ordered the parts which was easy to order through the internet and received them in a matter of days. I replaced them myself following the video instructions which were easy and simple to understand. Read more

Replace end caps. Read more

This story is somewhat unique, on Friday 5/23/14 I was cleaning the frig, when I broke the glass shelf. I went online to purchase a new glass shelf. Parts Pro said they would process my order if confirmed by 4:00 pm. and would ship it same day. I placed the order, and to my amasement the new shelf arrived 22 hours later, yes I said 22 hours. my hat is off to the Parts Pro. Thank you for such fast service, you now have a customer singing your praise as well as life long customer. Read more