Kenmore / Sears Control Board

This is a relay control board manufactured by Frigidaire to replace a broken or faulty part in wall ovens.In order for the appliance to work as intended, the relay control board needs to be able to receive signals from the main control board. It can then send relays that regulate the oven's various elements. Should this part be worn, faulty, or malfunctioning, the appliance won't work as intended, if at all, thus requiring replacement. To prevent injury, always wear work gloves and disconnect all power sources entirely from the appliance.This OEM relay control board is sold individually and manufactured from durable materials. It is compatible with wall ovens manufactured by various brands, including Frigidaire, Electrolux, Kelvinator, and Westinghouse.

Replacement LED assembly restores screen illumination by replacing the TV's failed LED strips. Use this part to address dim, flickering, or uneven backlighting and improve overall picture visibility. What it does:

• Replaces the TV's backlight LED strips to restore even panel illumination.
• Commonly used when the screen is dim, has dark bands or spots, or the backlight flickers or fails while a faint image remains.
• Fits into the original LED channels and connects to the existing LED driver/board (direct-fit replacement when matched to correct model).
• Does not address unrelated failures such as main board, power supply, or panel matrix faults.

• Disconnect power and allow the TV to sit unpowered before starting—work only when fully de-energized.
• Handle the LCD panel and assembly carefully to avoid pressure damage; wear ESD protection when available.
• Verify LED operation before full reassembly (power up with the panel/coverings off only if you are comfortable and it's safe to do so).

The Noise Filter is an OEM part for Whirlpool built-in wall ovens. It is installed inside the oven cavity near components that produce vibrations, such as the convection fan motor. 

Causes of a faulty noise filter include the degradation of noise-dampening materials over many heating and cooling cycles. Physical damage from accidental impact during cleaning could also compromise its sound-blocking ability.

Symptoms of a bad noise filter include: 

• Excessive buzzing or humming noises emitted from the oven cavity
• Louder than normal fan or component sounds carrying into the kitchen
• Vibrations felt externally on the oven chassis during operation

This OEM replacement fits several Whirlpool, KitchenAid, and Jenn-Air wall oven models.

3 pin 60 minute

The Oven Control Board is an OEM part for Frigidaire ranges. It is the central processor that regulates all heating functions, cooking modes, timers and safety features through electronic controls.

Causes of a bad control board can include moisture infiltration over time, loose connections, or component failures due to power fluctuations or surges.

Symptoms of a bad oven control board include:

• Elements not heating or cutting off as programmed
• Inaccurate temperature readings or inconsistent regulation
• Bake and broil modes not functioning properly
• Constant error codes or safety lockouts displayed

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This clock timer is the electronic oven control that governs timekeeping and oven functions. It displays the clock and settings and directs power to the bake/broil circuits so the oven responds to your commands.

• Controls and displays the clock, kitchen timer, and oven settings
• Sends power to bake and broil relays based on selected temperature and mode
• Coordinates preheat and cycle timing for consistent results
• Common signs it may be needed: blank or dim display, unresponsive buttons, error codes/beeping, oven won't start or heat though elements and power test good

• Disconnect power at the breaker before servicing—this is a high-voltage electronic part
• Access through the control panel or backguard; remove panel screws to reach the control
• Move wire connectors one at a time to the new control; reuse any mounting hardware
• Handle the board carefully to avoid static discharge; after installing, restore power and set the clock, then test oven functions

This part is a moisture sensor control board that is used on dryer units. This component monitors the moisture levels within the dryer and adjusts the dry time during the automatic drying cycle. A new moisture sensor control board will be needed if the time is not advancing in the automatic drying cycle, even if it does advance in the timed dry cycle. Another sign is if the dryer continues to run after the clothing inside is dry. Unplug the dryer from its power source prior to replacing this component. The person performing this task may wish to wear work gloves to protect their hands.The moisture sensor control board is compatible with dryers that are manufactured by Kenmore, KitchenAid, Kenmore Elite, Whirlpool, Amana, Crosley, Maytag, Inglis, Sears Canada, Roper, and Sears. This part is sold individually and it is a genuine OEM replacement part that comes straight from the manufacturer.

This is the relay control board for an range. This part receives signals from the main oven control board on the appliance. The function of this part is to operate relays to control the oven elements. Signs that the relay control board for an range has gone bad are if the broiler does not work but the lower element works fine or if neither is working. A visual inspection of the relay board will also be a good indicator. If the solder joints have sustained damage, then the entire relay control board will need to be replaced. Before attempting any work on the oven, make sure to unplug it from the power source. Wear gloves when performing care and maintenance on this appliance.This relay control board is made to fit ranges that are manufactured by Frigidaire, Electrolux, and Kenmore. This part is sold individually and is sourced from the manufacturer.

This RFI noise filter conditions the AC power entering your microwave, reducing electrical interference and helping protect and stabilize the control and power circuits. Replace it if the unit is dead or trips a breaker when starting.

• Filters radio-frequency/electromagnetic noise on the incoming AC line
• Helps stabilize power to the control, relays, lights, and fans
• Failure may cause no display or intermittent loss of power
• A shorted filter may blow the line fuse or trip the household breaker when plugged in or when Start is pressed

• Disconnect power by unplugging the microwave or switching off the dedicated circuit breaker
• For over-the-range units, remove the microwave from the wall to safely access internal components
• Label and transfer wires to matching terminals; mount the filter securely and route wiring away from sharp edges

This electronic oven control board manages oven temperature, bake/broil functions, and the display/keypad. Replacing a failed board restores proper heating and responsive controls so the oven operates and times as it should. What it does:

• Regulates power to the bake/broil elements or gas valve to reach and maintain set temperature
• Interprets keypad inputs and controls oven modes (Bake, Broil, Start/Stop, Timer)
• Drives the digital display for time, temperature, and status
• Common symptoms of failure: no display, unresponsive buttons, oven won't heat or overheats, or recurring error beeps/codes

• 1 electronic control board assembly

• Disconnect power at the breaker; turn off gas supply for gas ranges
• Use ESD precautions; handle the board by its edges
• Label and transfer wire connectors one at a time; move any mounting hardware/overlay from the original, if required
• After installation, restore power, set the clock, and test oven modes

Restore your dishwasher's brains with this control assembly. It manages cycle selection and timing so the machine responds to commands, starts reliably, and completes wash cycles without random beeps, stalls, or unresponsive controls.

• Coordinates cycle logic and component operation
• Interprets button/touch inputs from the console
• Drives status indicators or display on applicable models
• Typical symptoms: controls unresponsive, won't start, lights flicker or beep erratically, cycle won't advance

• Disconnect power at the breaker before servicing
• Use anti-static precautions; handle the board by its edges and avoid touching contacts
• Label/photograph wiring; move connectors one at a time and fully seat any ribbon cables/locks
• Reuse existing mounting hardware; ensure correct orientation and secure harness routing before reassembly

This defrost timer assembly cycles the refrigerator between cooling and defrost modes to prevent excess frost buildup and help maintain consistent temperatures. Replace a failed timer to restore regular defrost scheduling and reduce icing. What it does:

• Advances the refrigerator between cooling and defrost cycles on a timed schedule.
• Stops missed defrosts that can cause frost buildup on the evaporator and reduced cooling efficiency.
• Addresses symptoms such as excessive frost/ice, inconsistent temperatures, or a freezer that runs constantly.
• Acts as the control that engages the defrost heater and returns the unit to cooling when the cycle finishes.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Access the timer via the control panel or rear service area; document wiring or take photos before disconnecting.
• Install the timer in the same orientation and reconnect wires to the original terminals; do not force connectors.

This part is a timer that is used on washing machine units. The timer is a key component for the operation of the washing machine because it helps it advance throughout the cycles.There are symptoms that indicate that the timer has gone bad. One of the symptoms is that the washing machine won't turn off and it just continues to run. For example, it may be stuck in the spinning cycle longer than it should. If the timer will not advance, then it will need to be replaced with this genuine replacement part. For safety, unplug the appliance from its power source before attempting to work on it. Allow the washing machine time to cool down first.This timer is sold individually and comes straight from the manufacturer. It is compatible with washing machines manufactured by the Kenmore and Whirlpool brands.

This is the clock/timer assembly that controls the oven's timekeeping and bake/broil functions. Replacing a failed timer restores accurate time display and reliable oven control so you can set temperatures and cooking durations with confidence.

• Regulates oven functions through the electronic control (EOC), including bake and broil
• Displays clock and timer; enables timed bake features
• Common failure symptoms: blank or dim display, beeping/error codes, unresponsive buttons, oven not heating or shutting off unexpectedly
• Restores accurate time display and consistent oven operation

• Disconnect power before servicing; this is a live-voltage component
• Remove control panel/backguard screws to access the control; transfer wire connectors one-by-one to the new board
• Handle the board carefully to avoid static discharge damage
• Verify correct orientation and secure mounting before reassembly and testing

This electronic controller manages an appliance's user interface and core cycle functions so your unit responds to settings and runs programmed cycles. Replacing a faulty controller restores control responsiveness and cycle management. What it does:

• Receives inputs from buttons/knobs and runs the appliance's cycle logic
• Powers and updates the display and indicator lights
• Regulates timing, relays, and other outputs that start motors, heaters, or valves
• Faulty controller symptoms: unresponsive controls, incorrect or stuck cycles, no display or intermittent power, or visible error codes

• Disconnect power to the appliance before beginning any work to avoid shock or damage
• Handle the board by its edges and avoid static discharge; use a grounded wrist strap if available
• After installing, power up and test functions before fully reassembling the appliance

This inverter box is the electronic module that conditions and routes power to the refrigerator compressor, helping restore variable-speed compressor operation and consistent cooling when the inverter has failed. What it does:

• Regulates and converts power for the compressor's inverter drive to support variable-speed operation.
• Replaces a failed inverter module that can cause the compressor not to start or to run intermittently.
• Commonly used when the refrigerator runs warm, cycles abnormally, or displays inverter-related errors.
• Houses the control electronics for compressor power management.

• Always disconnect power before servicing the appliance to avoid shock.
• Access may require removing the rear or control housing panels; note wire routing and connector positions before disconnecting.
• Handle as an electronic component: protect from moisture, impact, and static discharge.