Kenmore / Sears Gasket & Seal

Took the whole dryer apart to access the wheels (4) of them, belt and fan wheel, also had to clean all the lint out that somehow builds up inside the dryer. Plus cleaned out dryer duct vent, added to the time involved. If you are planning on fixing the dryer because of a noise which was in my case, I highly recommend buy all the parts for complete maintenance mentioned above. What helped save me time? I watch a dryer fan wheel replacement training video first, highly recommend this!... Read more

Ordered replacement door seals, assistance picking the seals and speed of shipping was excellent. The installation was about as easy a job as can be, remove old seals, clean the doors and press in the new seals. With that said, I don't believe these are the same quality as factory original seals, the doors do not close as positive as the original and I have an air leak in the freezer door seal allowing condensation and ice to form. Read more

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

Removed front panel from refrigerator door and replaced the ice chute door seal and also replaced the seal inside the door that seals against the ice maker. Read more

Fairly simple fix. followed you tube video step by step..needed a set of extra hands (wife came in handy) when installing gasket..after several loads as a test, no leaks. Read more

The new gasket arrived in a box half the size of the gasket so the gasket was folded to fit into the box. I hung the new gasket up for a couple of hours and then just prior to installation used a hair dryer as per included instructions to soften the gasket and minimize minor wrinkles in the gasket. The old gasket came out easily and the new went in easily. A 5 minute job in total. Read more

Replaced Case Water Filter assembly DA81-05883A. Please read my post entirely before starting. I completed all the tasks that I could without having to disconnect the refrigerator since it was full of food. First I removed the panel on top of the refrigerator that covers the water line that feeds the dispenser. Do not disconnect any electrical connections or the water line at this time. Remove the panel from the back bottom of the refrigerator that covers the compressor and water valve,... Read more

I ordered the gasket with the model number off the frig. AppliancePartPros.com made it easy to find my part. There was also a "how to" video on the same page. I ordered the part and it got to OH the next day. Following the video guideline it took me 15 minutes to remove the door, strip out the old seal and put in the new one. I will be ordering all my appliance parts from AppliamcePartsPros.com Read more

• Door sweating

The video explains exactly how to remove the old refrigerator gasket and replace with the new one we ordered. Thank you for detailed explanations of how to do this project. Read more

Located appropriately sized door gaskets. Read more

Followed directions on video, worked as advertised. The only trouble I had (if you can call it that) was with removing the door. I have a freezer on top not side by side. Its easier to take the door off a side by side. When doing one like mine it can be done with one person but it's nice to have an extra set of hands to hold the door in place when removing the bracket which is on the bottom, You can take the freezer door off if you want and work your way down to the fridge door but I didn't... Read more

The gasket on my freezer door was not holding the door closes. When the main door closed, the pressure which shifts to the freezer was popping the door open and it was not closing because the magnet had lost its' mojo. I watched the video for the replacement of the gasket on the freezer door and my experience was exactly the same. One area that you should be mindful of: the depth of the fin on the replacement gasket is short, so do not make the slot of this fin too deep. When you are... Read more

My 12 year old Frigidaire stack on top dryer had been beeping distress messages in some unintelligible code for about a year when it completely stopped producing heat. It also had a long standing issue with delicate fabrics and thin straps or drawstrings getting caught in the drum. After using this site to troubleshoot and viewing the useful how-to videos, I ordered and replaced the heating element, thermal limiter, and felt seals. Based on others' stories, I decided to also replace the rear... Read more

• Door sweating

I went on the web and put in the refrigerator model. Several parts websites came up; I explored them all. All were approximately the same price, but I clicked on the installation video from AppliancePartsPros.com and was impressed with the thoroughness of the instructions. I knew it would be a huge help in putting on the gasket. So I ordered the gasket from them and it was delivered as promised. All in all, a very good transaction. Read more

Removed existing gasket and replaced with new gasket in less than 5 minutes. Very Easy. Make sure to remove the lower burner cover (inside the oven) which allows you to pull the end gasket material through the two circular openings in the frame. Read more

First tried replacing the seal around the door as that was the simple and most logical fix. Still leaked. Removed the front and upper panel to inspect. Found calcium deposit running down from under the Air Vent Assembly and wet behind the black stick-on insulation. Easy to trace the leak to the bottom of the door. => Ordered new Air Vent Assembly, gasket and Vent Deflector. Parts arrived. Took 5 minutes to remove upper panel. Removed the two wires from the Air Vent Assembly. Inserted a... Read more