Kenmore / Sears Gasket & Seal

Ordered both the door seals, they arrived in two [2] days. It took less than 20 minutes to remove the old seals and install the new seals. Super easy to replace. Read more

First I watched the very, very helpful video (twice), then I planned out the job in regards to tools, work area, and access. I have stacked units of washer/dryer due to space restrictions and had to ask my son-in-law to help me lift the dryer of the washer once I had prepared the process by fabricating 2 pieces of 3/4" plywood to turn the dryer and then slide it out far enough were 2 people can lift it and then set it on some cribbing for easy handling. Disconnected the power, turned off the... Read more

Bought gasket from website, followed easy helpful video instructions, perfect fit. Read more

Replaced gasket. Video did not account for need to remove screws and gasket stays. Took a little time to figure out the best way to install new gasket. Installed metal gasket stays in four sections of the new gasket and then carefully lifted assembly into position before re-installing screws. Read more

I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more

• Freezer section too warm

I ordered the replacement gasket and...replaced it. One issue was that the replacement procedure was not at all like the video to which I was directed when I got the gasket. The video showed a gasket with a rigid flange that had to be inserted into the door structure. On my Amana, I clearly had to remove the inner plastic liner and set the gasket under it. This was not particularly difficult but certainly wasn't the same process. Also, I removed the freezer door to do the replacement in... Read more

This was super easy! I ordered the replacement seals from AppliancePartsPros, they also had a video showing how to do it. Once I received the set I simply removed the old ones by pulling them away from the door. I took the new ones and pressed them into place. The only tool needed, was a screwdriver to remove the door divider from the left door. Note- the seal for the left door is different from the right door so you will want to be sure to compare the new seals to the old seals before... Read more

Replaced the gasket Read more

Pulled out old parts, and swapped with new. New seals needed to be warmed up with a hair dryer to get wrinkles out from shipping, but that was simple as well. With my fridge, there was also a secondary piece on the door which needed to be removed with a screw. Took some extra time to give all those surfaces on the fridge a much needed cleaning while the seals were off. New seals fit perfectly and the replacement was simple- video provided on the website was also helpful. Read more

Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more

With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)... Read more

Replaced dispenser. It was hard to snap into place. You don't need to order separate gasket it comes with it. Read more

I nearly shelled out for a new Kitchenaid when I remembered APP and entered my model # just for fun. The interactive diagrams and install videos showed where all the parts "should" be, mine were badly disintegrated, so I replaced the damaged ones and swapped out all of the other easily accessible seals and bearings (also gave it a good and very disturbing cleaning). My parts surprisingly arrived next day and for about $40, the dishwasher is quiet and works like new again. Read more

Replaced the door seal I will not know for 2to3 weeks if that fix it or not Read more