Kitchenaid Control Board

The Control Board is an OEM part for Whirlpool dishwashers. As the central processing unit, the control board orchestrates each cycle by coordinating motor, pump, heater and other component functions. It monitors cycle progression, temperatures and safety features.

Causes can be circuitry damage from power surges, water damage or normal component wear over time. Control boards experience constant usage with each cycle.

Symptoms of a bad control board include:

• The dishwasher not starting or powering on properly
• Inoperable or unresponsive buttons/controls
• Inability to advance through wash cycles
• Error codes displayed
• Cycle functions become intermittent

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Restore reliable operation with this Electronic Control Board. It serves as the appliance's brain, interpreting user inputs and sensor feedback to coordinate functions and power the proper components when the original board has failed or become intermittent. What it does

• Processes keypad/touch inputs and executes programmed appliance logic
• Directs power or control signals to components as required for operation
• Monitors sensors/feedback to manage performance and safety routines
• Failure symptoms can include a blank/unlit display, unresponsive controls, won't start/complete a cycle, or recurring error codes

• 1 electronic control board

• Disconnect power at the breaker or unplug before servicing; verify no power is present
• Use anti-static precautions; handle the board by the edges and avoid flexing it
• Label or photograph wiring, then transfer connectors one at a time to the new board
• Ensure all harnesses are fully seated and the board is secured before restoring power and testing

This is an electronic control board for refrigerators. It's an internal component that ensures the refrigerator runs correctly at all times. The electronic control board is used to manage temperatures, defrosting times, and other features in the refrigerator. If this part is damaged or worn, it may cause cooling issues, prevent the appliance from working, or cause erratic behavior. In some cases, it will also make a whistling or clicking noise.If the electronic control board is malfunctioning, it will need to be replaced. Tools needed include a Phillips screwdriver, flathead screwdriver, and needle-nose pliers. A pair of work gloves can also be useful to protect the hands. Before starting work with the control board, unplug the refrigerator or turn off the circuit breaker. Locate the control board cover, remove the screws, and take off the cover. Detach the wires and take out the electronic control board. Replace the wires in the appropriate places on the new board and install it into the refrigerator.This is an authentic OEM replacement electronic control board. It's sourced directly from the manufacturer and designed for use with refrigerators by Maytag, Whirlpool, KitchenAid, and Kenmore. This component is sold on an individual basis.

This electronic control board is the central "brain" of your appliance. It manages power distribution, sensor inputs, and timing so selected functions run correctly. Replacing a failed board restores proper operation and reliable, responsive controls.

• Coordinates and sequences operations based on user selections and built-in programming
• Interprets inputs from sensors/switches and communicates with the user interface
• Drives components such as motors, pumps, valves, and relays as required
• Common symptoms of a failed board: appliance won't start or respond, cycle won't advance, stops mid-operation, intermittent behavior, or error/blinking status codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the PCB by the edges to avoid static damage
• Photograph wiring and transfer connectors one at a time to the new board
• Some models require service-mode setup or programming after installation—follow the tech sheet for your unit

This electronic control board is the appliance's command center. It reads inputs from switches and sensors, then directs power to components to run selected cycles—helping restore reliable operation when the original board fails.

• Coordinates timing and power to key components
• Interprets user commands and sensor feedback
• Manages cycle logic and stores/communicates fault codes
• Failure symptoms include no power, unresponsive controls, cycles that won't start or complete, or intermittent operation/error codes

• Disconnect power at the breaker before servicing
• Use ESD precautions; handle the board by the edges and avoid touching circuitry
• Note/photograph wiring and move connectors one at a time to the new board
• Inspect connected loads (motors, heaters, valves, fans) for shorts before powering up the new board

This electronic control board is the dishwasher's brain, managing cycles and powering the pump, valve, heater, and other loads. Replacing a failed board restores normal start, wash, drain, and dry functions.

• Coordinates and times wash cycles based on user selections and sensor inputs
• Sends power to the circulation pump, drain pump, water inlet valve, and heater
• Interfaces with the user interface and monitors door/latch status
• Failure may cause: no start, cycle won't advance or ends early, no fill/drain/heat, or error codes

• Disconnect power at the breaker before servicing; verify power is off
• Access location varies by model; commonly behind the lower toe panel or inside the console
• Handle the board by the edges and observe ESD (anti-static) precautions
• Move wire connectors one at a time from the old board to the new, secure the board, and reassemble; run any required diagnostics/reset per your model's tech sheet

This is a high-quality refrigerator power supply board. It's an internal component that is made to control the refrigerator functions. This part is made with small precision parts to help with timing defrost and cooling cycles. This part can be damaged or malfunction and stop operating correctly. This may prevent the refrigerator from running, cause strange sounds, or cause the refrigerator to run at the wrong temperature.If this part is damaged, it will need to be replaced. Before replacing the power supply board, make sure the refrigerator is unplugged from the wall. The process will require a flathead screwdriver and a nut driver. Use the tools to unthread the screws on the access cover. Depress the retaining tab to remove the inner cover and disconnect the wires. Press the tab to release the power supply board and snap in the new component. Make sure the wires are properly connected and reassemble.This genuine OEM replacement part is sold on an individual basis. It is directly acquired from the manufacturer and is designed to be compatible with refrigerators made by Kenmore, Whirlpool, Maytag, and KitchenAid.

This electronic control board is the dishwasher's main circuit board. It directs wash, drain, and dry functions and coordinates the user interface. Replacing a failed board restores responsive controls and reliable, complete cycles.

• Times and sequences wash, drain, and dry operations
• Distributes power to the circulation pump, drain pump, inlet valve, and heating circuit
• Monitors sensors and door switch; communicates with the display/indicator lights
• Common symptoms: won't start, unresponsive controls, cycles that stall or never advance, blinking lights or error codes

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use ESD protection and handle the board by its edges
• Label/photograph connectors; transfer any mounting brackets or jumpers from the original board
• Some models require configuration/programming after install—follow the tech sheet stored inside the unit

This defrost timer cam replaces the plastic cam on a mechanical defrost timer. It restores the timer's changeover between cooling and defrost, helping prevent frost buildup on the evaporator and temperature swings inside the refrigerator.

• Mounts on the timer shaft to actuate the internal switch between cooling and defrost
• Helps resolve issues like heavy frost on the evaporator, warm fresh food section, or a unit stuck in defrost/run
• Corrects timer advancement problems caused by a stripped, cracked, or missing cam
• Typically installed with the defrost timer in the control housing or rear service area

• Disconnect power before servicing
• Access the defrost timer and note the original cam's orientation for reference
• Remove any retainer, pull the old cam straight off, and press the new cam fully onto the shaft without forcing
• Reassemble, then manually advance the timer to confirm it switches modes before restoring power

This speed control regulates and stabilizes motor speed in your appliance. Replacing a faulty control restores smooth start-up and accurate speed selection so the motor runs consistently at the setting you choose.

• Modulates power to the motor to reach and hold the selected speed
• Helps correct issues like surging, stalling, or running only at one speed
• Common symptoms include erratic speeds, failure to start, or sudden speed changes
• Also presents as an unresponsive speed selector or inconsistent performance

• Disconnect power before servicing and allow components to discharge
• Access the control per your model's service information; note wire locations or take photos
• Transfer connectors one at a time; seat fully and handle electronics with ESD care
• Reassemble and test operation through all speed settings; perform any model-specific calibration if required

This replacement part is an oven control board and display. It houses the buttons that users push to control oven operation, including bake functions, temperature, and access to the timer and clock. Over time and through exposure to heat and moisture, the control board may corrode and fail. If the control board is damaged, the oven may not operate correctly or at all.To replace the oven control board, first unplug the oven from the wall. Next, remove the rear access panel from the stove. This should reveal the back of the control board. Remove the mounting screws and disconnect the wiring. Remove the old control board. When ready to install the new board, first remove the protective film, then place it on the slot. Install the mounting screws and reconnect the wiring. Replace the oven's rear access panel. Always wear gloves when repairing an oven.This is a genuine OEM replacement part. It's manufactured by Whirlpool and will fit Whirlpool, KitchenAid, and Kenmore ovens.

This is a refrigerator control board that can be used to replace a damaged or faulty board in select refrigerators. The control board is used to manage various functions that occur in the refrigerator, including cooling and defrosting. If there is a problem with the board, the refrigerator might not be able to defrost correctly, or it might not stay cool.The control board for the refrigerator tends to last a long time. However, it could eventually wear out and stop working. It could be damaged due to a voltage surge, or it might be a faulty board. Remove and store all food in the refrigerator and unplug it before beginning repairs.This refrigerator control board works with certain models from Kenmore, Whirlpool, KitchenAid, Roper, Estate, Inglis, Crosley, Gladiator, Kirkland, and Maytag. It's sold individually and is a genuine OEM replacement.

This electronic control board is the appliance's central controller, managing critical functions and timing. Replacing a failed board restores proper operation, responsive controls, and consistent performance when the unit is unresponsive, shows errors, or behaves unpredictably.

• Processes user commands and internal signals to run cycles as designed
• Controls or communicates with motors, valves, fans, and heaters through onboard components
• Manages timing, temperatures, and safety checks programmed by the manufacturer
• Symptoms of failure: won't power on or start, dead or erratic controls, error codes, intermittent operation

• Disconnect power to the appliance before servicing; also shut off gas/water
• Use anti-static precautions and handle the board by its edges
• Photograph connections; transfer connectors one at a time to the new board; secure in the original mounting
• After installation, follow your model's tech sheet for any required initialization/diagnostics and verify normal operation

This electronic control board is the central "brain" of the appliance. It manages cycle timing and directs power to key components, helping restore proper operation when the original board fails or becomes intermittent.

• Coordinates cycle timing and logic for the appliance
• Monitors inputs from sensors and switches, then executes the correct program steps
• Distributes power to loads such as motors, pumps, valves, fans, and heaters
• Failure symptoms can include no start, won't complete a cycle, erratic operation, error codes, or components not receiving power

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the board by edges and avoid touching connector pins
• Photograph wiring and transfer any brackets or covers from the old board; seat all connectors fully
• Reinstall panels and run the model's diagnostic or test cycle per the tech sheet to verify operation

This oven control board is manufactured by Whirlpool. It is an electronic component and is responsible for monitoring and controlling the oven's functions, such as bake, broil, and warm, as well as maintaining the appropriate temperature set by the user. This control board does not include the physical controls for the oven.High heat and exposure to moisture can degrade the control board. This may result in intermittent problems or outright failure of the oven. In both cases, the control board will need to be replaced. Before working on the oven, make sure to unplug it or shut off the circuit breaker. Wear gloves at all times and exercise care when disconnecting/connecting the writing to the board.A genuine OEM part, this control board is sold individually. It fits Whirlpool and KitchenAid branded ovens.

This electronic control board is the refrigerator's central control module, coordinating cooling and defrost functions for stable temperatures. Replacing a failing board helps restore proper operation of the compressor, fans, and related circuits.

• Regulates cooling by switching the compressor and fans based on sensor input
• Controls and times the automatic defrost cycle to prevent frost buildup
• Supplies logic and power to temperature controls and indicators
• Can cause no-cool, intermittent cooling, constant running, or unresponsive controls when faulty

• Disconnect power to the refrigerator before servicing
• Handle the board by the edges and use ESD protection if available
• Photograph/label connectors and transfer wiring one at a time
• Some models require control setup or calibration—follow the appliance's service instructions