Kitchenaid Control Board

I could not find specific online instructions for this job. Here are some tips. 1. Unplug the washer. 2. Unscrew the dial on the broken timer. 3. Gently pry up the thin plastic place-indicator plate (the thing with the arrow under the dial) with two flathead screwdrivers. 4. Unscrew the two hex screws holding the old timer in place. 5. Unscrew the phillips-head screws holding the console in place and flip up the console. 6. Remove the electrical connector from the bad timer, and remove the bad... Read more

• Won't start

Tried to put refrigerator in defrost mode and defrost would not initiate. Checked the bi-metal and heater, both tested good. Replaced the ADC board and refrigerator went in to defrost. problem solved. Read more

• Freezer section too warm
• Fridge too warm

Replaced the heater, timer, and wiring harness Read more

• Won't start

I purchased a new igniter for the bake assembly and found that it, unfortunately, did not resolve my problem. I measured the resistance of the different points on the gas valve and it was reading within spec so I then purchased this spark module and it did the trick. My gas range is a Kitchenaid kgsk901sss02. I had a LOT of trouble finding where the spark module is located, and eventually found a schematic that shows it's location behind the front control panel of the oven. Upon taking the... Read more

Removed and replaced part arrived sooner than expected thank you so much!!! Read more

After looking for solutions online and watching some short videos, we decided to open the dishwasher up and try to fix it ourselves. We opened it up and found the circuit board had burned out causing a horrible odor. We ordered our new board, popped it in and we now have a working dishwasher. Hooray! Read more

We started getting the F06 code when on the normal cycle it was time to Rinse/Spin, pointing to a speed/tachometer issue on the motor. After several attempts of unplugging from power and restarting the cycle it would eventually start working for the rest of the laundry session. The Whirlpool technician after a brief look on the underside determined it was the motor and had to be replaced, even tough all troubleshooting tests on the motor were ok. I insisted that the probability was much higher... Read more

Bought new optic control boards, both the emitter and the receiver. The repair process was so simple. The KitchenAid repair tech came out to diagnose our issue. He was only going to come back and install a new emitter. They wanted a lot of money to do the repair. They were going to charge us $257 just for the part (emitter board). We bought both boards for $300 from AppliancePartsPros. We decided to replace both boards, because if one went bad the other might not be far behind. Read more

Replaced the control board. It was easier than I thought it would be. Read more

Replaced numerous items including this Inverter and two control boards but the Magnetron was the ultimate solution. The tip was clearly burned through when I removed the original. Read more

The refrigerator was given to me and hasn't defrosted since it was new. I found the defrost timer had a burnt spot on the circuit board. After installing a new timer, the refrigerator would trip the circuit breaker in my house when it entered defrost mode. I found that the pink wire running from the control board all the way to the thermostat was shorted somewhere between the two parts, inside the refrigerator. I ran a new "pink" wire and all is good. Read more

The 20 year old unit still serves us well, looks good and has been kept in good repair. The condenser fan had stopped so I removed, cleaned and oiled that motor. The decision was made to make an upgrade to the evaporator motor and control units so that the appliance could reasonably be expected to have extended service life. The Ice maker module had been replaced 7 years ago. I ordered the parts and have made the upgrade for temperature controller and the defrost control. If you are in a... Read more

Replaced all 3 circuit boards and now waiting two weeks to see if the problem returns or not... Read more

I initially purchased a door switch, thinking that it would solve the problem. I replaced the switch by removing the top 6 star screws, removing the component cover and removing one of the door switches (using a 3/16 socket) with the new one that I bought but I still had the problem. Looking at the schematic, the next part that needed to be changed is the electronic control board, which I purchased. I removed the same screws again and cover, used a screwdriver to pull back the clips holding... Read more

Replaced the control panel. Very simple because you had a "how-to" video for my exact model. Read more