Kitchenaid Parts

• Ice maker dispenses too little ice
• Not dispensing water
• Touchpad does not respond
• Leaking

I'm such a pro, I figured I needed a new hose for my water dispenser so I ordered it. When it arrived I called my handyman. He told me I did not need a hose I needed A cartridge. So I had to return the hose and order the cartridge! Your company was so cooperative and made the return so easy Thank you! Next time I call the handyman first! Read more

Pulling the dishwasher, it was obvious we had a slow leak under it. We had a slow leak from the diverter motor area in the sump. Sure enough, it looked like the gasket around a shaft had to be the culprit. The gasket was attached to the sump assembly, or the motor. We took a chance and ordered a new sump assembly for a mere $90 and went for it. All of the trays had to come out. The lower spray arms. Then the distribution runs to the middle rack arms and upper rack arms. Finally, the original... Read more

My refrigerator was not dispensing ice. I could hear the motor activating but noticed the ice auger was not turning. My old drive shaft was stripped on both ends. Video was very helpful and it was an easy fix for someone with little handyman experience. Received my order much faster than expected! The parts arrived the next day and paid for the standard shipping charge. I live in Texas. Read more

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

• Fridge too cold
• Freezer too cold
• Fridge too warm

Toughest part of this repair is figuring out how to get things apart. Amana doesn't provide you a repair manual showing how to disengage the various plastic covers. Initially disassembled the bottom freezer compartment so I could get to the evaporator coils; they were completely frozen in block of ice, restricting air flow to the fridge above. Obviously, the auto defrost cycle had not been running, or was short-cycling. Manually defrosted. Found this link for running diagnostic tests on the... Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

• Burning smell

All's well that ends well, but the getting there was a bit of a pain. The web site suggests 3 possible causes for my problem (incl. the burning smell). I began with the first two since they were inexpensive compared to the motor, which was the third cause (and also the least often cause). There is no way to visibly tell if the motor is bad or not. After replacing the clutch assembly, which did have some plastic pins broken off) and the motor coupling (which actually looked fine, but the... Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

After taking the two vegetable drawers out from above, the glass shelf, the pantry drawer and the cross support for the glass, you can get to the two recessed hex head screws holding the end cap. You will need to transfer the metal drawer slide to the new cap, but it doesn't need to come off first. When the end cap is loose, gently rotate it toward the front. Once the humidity control slide is at 90 degrees from the back of the refrigerator, the tab holding it in place will slip out easily.... Read more

• Won't start
• Element will not heat
• Little to no heat when baking

I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more

It was an extremely easy fix with this video https://www.youtube.com/watch?v=l2YpWoE-BUA Read more

• Noisy
• Fridge runs too long
• Fridge too warm
• Freezer section too warm

Unplugged refrigerator and removed access panel from back of fridge. Have had this panel off many times for dust removal. Panel is a cheap piece of glorified cardboard on this Whirlpool model, which is a shame given that it was a $1000 refrigerator. Fan motor is mounted on stamped sheet metal bracket which I removed from cabinet with old fan attached to it. Metal bracket held in place by 4 1/4 inch hex head sheet metal screws. Two outermost screws can be removed with nut driver but access to... Read more

Removed old lint filter, inserted new one. Read more

• Fridge runs too long
• Noisy
• Freezer section too warm
• Fridge too warm

After reviewing the 'how to' video on AppliancePartsPros.com, I unplugged the refrigerator and removed the back cover to access the motor. I then unplugged the wiring and removed the bad motor. I cut the clip plug and wired it to the new motor, installed the fan blade from the old motor and re-installed the new motor. After connecting the clip plug and re-installing the back cover, I plugged the refrigerator in and checked the interior about 5 minutes after the repair. Everything has been... Read more

I researched the correct part I needed and ordered it. The part arrived in only 2 days. Installation was easy and the refrigerator is like new again. Read more

Ordered a new filter and filter holder Read more