Kitchenaid Parts

Very easy fix. Unplugged microwave, then lowered bottom panel, removed the two leads to the turntable motor, removed two screws attached to motor, removed old motor, put new spacer on motor stem, installed motor with same two screws, reattached the two wires, reattached panel ( after cleaning all the grease that built up over the last 6 years), plugged microwave in and good as new! Took me twenty minutes. Note: the two screws holding the motor were not Phillips like those holding the panel. So... Read more

Just replaced it Read more

• Not dispensing water
• Ice maker not making ice
• Leaking

A piece of cake. Video was spot on. Finish less than 45 min. Read more

Dishwasher needed to be disconnected from power and water supplies, removed from the cabinet and placed on it's back to gain free access to the underside of the unit. The motor-pump unit removed ( just three screws and two wire connections ). Once the motor unit is removed, the filter-pump part 'rests' on the end of this unit and just lifts off. The new part is put in place and the motor is re-attached, minding to make the metal support arm goes back inside the rubberized carrying slot and... Read more

Put in a new infinite switch behind the knob to control temp level. Read more

• Won't start

Replaced igniter---works great---saved service call. Read more

Cleaned the slide areas really well and ordered new drawers. Read more

Found the part # on manufacturers website. Ordered it from ApplianceParts Pros. Watched a video of repair on Youtube. Fix was done n about 10 mins. ApplianceParts Pros had the part cheaper than manufacturer. Delivery was prompt. Replacement easy. Read more

I look on the internet i came a cross appliance parts pros i didnt no what i was looking for so i call the phone number talk to someone gave him the info he ask for they has what i was looking for in stock the guy was very nice he say i will get the part in two days and i got it in two days if i need a part for anything else i will ckeck out appliance parts pros when the door gasket came my grandson put it on in a flash Read more

Easily. Read more

• Freezer not defrosting
• Frost buildup
• Fridge too warm
• Fridge runs too long

I am not new to APP, fixed a tub belt on a Maytag dryer in the past. My frig started getting warm so I went onto to one of those "lists" sites and found a appliance repair place. The guys were great and came out right away. The tech said it was the cold control and $260 later my part was replaced, about 30 minutes. Great I thought until my frig started getting warm again. Those cold sensors on the beer bottles are a great indicator. Not wanting to spend another $260 I looked up on APP to see if... Read more

Replaced door closure and door stop. Read more

I took the new seal out of it's packaging and used a blowdryer on low heat to soften up the seal so that the crease from shipping (it was folded to ship) disappeared. Next I took the refrigerator door off, removed the old seal, & cleaned the area where the new seal would be applied. Following the video on the Appliance Pro Parts website, I re-installed the new seal and put the door back on. Last step was to snap on the new hinge cap I ordered. The video online was easy to follow and this... Read more

I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more

I'm not an appliance mechanic and have never worked on a dryer before, but I have worked as an instrument technician and lightly dabbled in HVAC repairs. We moved from natural gas to a new home with propane, so purchased this kit to make the conversion. In my mind I thought it would be fairly quick and easy, change a few fittings, etc, but realized upon reading the instructions that I needed to disassemble most of the dryer. The work was straightforward but since this was my first time... Read more