Lg Valve

This water inlet valve controls water flow into the appliance, allowing the correct amount of water to enter during fill cycles so the machine can wash properly and drain when commanded. Reliable operation helps prevent no-fill or overfill symptoms. What it does:

• Opens and closes to allow water into the washer during fill cycles.
• Enables correct water level and filling timing when signaled by the control board.
• Commonly replaces failing valves that cause no-fill, slow-fill, continuous filling, or leaking at the valve.
• Works with standard inlet hoses and connector fittings used on compatible washers.

• Disconnect power and shut off the water supply before servicing.
• Note hose and electrical connector locations before removal to ensure correct reinstallation.
• Tighten water connections securely and check for leaks after restoring water and power.

This inlet valve assembly controls the flow of water into the washer so cycles fill correctly and on schedule. A direct-fit replacement that restores proper water delivery and helps prevent overfilling or no-fill conditions. What it does:

• Opens and closes to allow cold and hot water into the tub during fill cycles.
• Responds to the washer's control signals to deliver the correct water amount.
• Commonly replaces a valve that leaks, won't fill, fills slowly, or causes continuous filling.
• Helps resolve related error codes or fill/level issues when caused by a faulty valve.

• Disconnect power and shut off both water supply lines before starting work.
• Drain remaining water from hoses and use caution when handling connectors.
• Inspect inlet hoses and seals; replace damaged hoses or seals to prevent leaks.
• After installation, restore water and power, then run a short test cycle to check for proper fill and leaks.

This surface burner valve controls gas flow to a cooktop burner for reliable flame adjustment and safer operation. Replaces a worn or leaking valve to restore consistent heat and proper burner control. What it does:

• Regulates gas flow to a single surface/burner for simmer-to-high flame control
• Stops gas flow when turned off to prevent leaks
• Addresses symptoms like weak or uneven flame, burner not lighting, or gas odor (stop use and check immediately)
• Works as the control point between the cooktop knob and burner

• Turn off the appliance power and shut off the gas supply before starting any work
• Work in a well-ventilated area and check for gas leaks after installation using a leak-safe method (soap solution or approved detector)
• Use proper tools and replace any damaged fittings or seals; tighten connections to manufacturer torque where specified

The Water Valve Assembly is an OEM part for LG refrigerators. It controls the flow of water into the refrigerator's ice maker and water dispenser, ensuring a steady and controlled supply. This valve opens and closes in response to electrical signals from the refrigerator, allowing water to enter the appropriate compartments for ice making and dispensing.

Over time, the water valve can wear out or become damaged due to mineral deposits, wear and tear, or electrical issues. A malfunctioning water valve can lead to problems such as water not dispensing correctly or the ice maker not producing ice.

Symptoms of a bad water valve assembly include:

• No water dispensing from the refrigerator
• Ice maker not producing ice
• Leaking water from the valve area
• Unusual noises coming from the valve

This OEM LG part is also compatible with Sears/Kenmore.

This water inlet valve assembly controls and regulates the flow of water into your washer during fill. A working valve helps the washer start and complete cycles reliably without leaks, overfilling, or long fill times.

• Opens and closes to allow household water to enter when the control calls for a wash or rinse
• Shuts off water flow when not energized to prevent unwanted filling
• Helps maintain proper water levels and flow for consistent performance
• Common symptoms: no fill or slow fill, continuous filling or overflow, leaks at the valve or hose connections, or buzzing with little/no water flow

• Unplug the appliance and shut off water supplies before servicing
• Place towels or a pan to catch residual water and relieve line pressure
• Label or photograph connectors/hoses; transfer them one at a time to the new valve
• Tighten hose fittings snugly and run a test fill to check for leaks

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker so you get reliable ice and chilled water. Replaces a failed valve to restore proper water supply and prevent interruptions. What it does:

• Opens and closes to route household water to the dispenser and ice maker when activated
• Helps ensure proper filling of the ice maker and water dispensing
• Can cause no water from the dispenser or ice maker if failed or clogged
• May leak or drip when seals or diaphragms wear out

• Disconnect power and shut off the water supply before starting work
• Replace only with the exact part number; inlet/outlet fittings match your unit
• Inspect supply lines and electrical connectors for damage; tighten or replace as needed

This water inlet valve controls the flow of water to the refrigerator's dispenser and ice maker, restoring proper water delivery for ice production and dispensing. It's a direct-fit replacement that helps stop leaks and restore normal water flow. What it does

• Opens and closes to allow water into the ice maker and dispenser when called by the refrigerator's control system
• Commonly replaces valves that are leaking, stuck closed, or failing to supply water
• Helps correct symptoms like no ice production, weak/slow water dispensing, or visible leaks at the valve area
• Works with the fridge's water line and solenoid system to regulate water delivery

• One water inlet valve assembly

• Disconnect power and shut off the house water supply before starting any repair
• Only install if you can access the valve and water line connections; use proper tools to avoid damaging fittings
• Inspect and replace any worn inlet hoses or seals while accessible to prevent future leaks