Lg Valve

Once I was convinced that the water supply and filter wasn't the problem, I took the back protective panel and looked at the valve assembly. It looked corroded, especially on top where the ?pistons for the solenoids?would project into. I ordered the part and it was on my doorstep in TWO days...really fast. The part was slightly different from the one that I was replacing in that the part was "angled out." This was not a problem. All that did was tilt the fitting for the copper water line... Read more

Ordered the and part fixed it myself. Read more

Ordered new pump with reservoir and installation was easy Read more

The hot inlet valve was dripping water, replaced it. Water and soap were coming out of the vent pipe. The new Float assembly had a shorter shaft than the old Float Assembly I was replacing. I did install the new Float Assembly and cleaned the vent hose where the float seats and I haven't seen any more water on the floor. Both repairs were made easy by watching your repair videos. Read more

Replaced water inlet valve Read more

• Will not fill with water
• overflowing

The insulation in my old Ohio house is terrible, and the Valve Assy, Inlet part under my dishwasher must have froze and burst when the temperature outside got below 0. I ordered this part here, and literally got it the next day. Awesome. The how-to video on the site was perfect. Not only did I replace the part in about an hour, but I saved ~$200 by canceling my LG service repair appointment. Read more

Determined it to be the water inlet valve assembly. Found part on AppliancePartsPros. Good price and fast delivery. Luckly the part was easy to get to and replace with no issues. Read more

I bought a new controller first and installed it. The exact replacement controller was no longer available and I had to modify two AC connectors that changed from 3 pins with two wires to two pins with two wires. This was not expected but I made it work just fine by getting the three pin connectors on the cable to fit the two pin by breaking out the center web in the board two pin and then shaving off the raised key plastic on the wires. Then on power up, I found that the wash motor did not... Read more

• Will not drain

So all of a sudden the dishwasher stops working, "0E error"on the panel. Did some google searches and found that it might be the filter, which I did not know needed to be changed, or worse, the motor. Took the filter off per online tutorial (easy) and mopped up all the stagnant water. Poking around, I find the small rubber check valve that has broken. Had to fish it out with tweezers. Long story short, it was not the motor and I doubt it was the filter. It was this $1.87 rubber drainage... Read more

First determined drain discharge hose was clear. Turned of power to dishwasher. I did not find it necessary to remove the dishwasher. I simply removed the lower service panel at the floor and was able to easily remove the defective pump, unplug it, replace the small rubber check valve flapper before the pump inlet and reinstall the new pump assembly. The dishwasher surprisingly cleans and runs quietly like new again although I found no excuse for the pump failure as it is well designed. Never... Read more

Had to replace the water inlet valve for both hot and cold. After a quick chat with customer support that verified the correct parts for the FE error and placed my order the, the parts arrived quickly. The video and diagram helped with the repair, and now the machine is now running better than when we first got it. Thanks so much!! This is our second time ordering from AppliancePartsPros. Both times have now proven that this is the place to shop for all things appliances and repair support. Read more

I first replaced the drain hose, as this seemed to be a common problem with LG. The washer continued to leak, I then noticed it was leaking from the valve assembly, inlet. It took 10 minutes and now the washer works fine with no evidence of water. Read more

• Will not fill with water
• overflowing

I replaced the valve. Read more

I ordered both the hot and cold water inlet valves because I wasn't sure which one may have been faulty. I installed them exactly the way the on line video showed, tested them and reinstalled the top of the washer. Checked several days and have found no sign of water. This was such an easy fix! Read more

I replaced both items. And it was easier than I thought. Read more