Maytag Dispenser Parts

This genuine replacement pad provides the specified cushion or contact surface in your appliance. Replacing a worn, flattened, or missing pad restores proper fit, helps quiet operation, and protects adjacent parts from rubbing and premature wear.

• Provides the designed cushion/spacing or contact surface between components
• Helps dampen vibration and reduce rattles or squeaks in the area of use
• Protects finishes by preventing metal-to-metal or plastic-to-metal contact
• Restores proper alignment or smooth actuation where a pad is specified
• Common signs it's due: missing pieces, cracking, compression, residue, or new noises from that location

• Disconnect power (and water, if applicable) before servicing
• Access the pad location per your model diagram; note original placement and orientation
• Clean the mounting surface; if adhesive-backed, peel liner and press firmly; if clip- or friction-fit, seat fully
• Reassemble and test for proper fit, quiet operation, and smooth function

Color: White

This fabric softener dispenser replaces a worn or missing cup in your washer. It holds liquid softener and releases it automatically during the rinse cycle for even distribution and cleaner results without residue on clothes. What it does:

• Holds liquid fabric softener and dispenses it at the proper time in the cycle
• Helps reduce spotting or residue from pouring softener directly into the tub
• Replaces cracked, missing, or clogged dispensers that may leak or fail to dispense
• Restores consistent, mess-free softener delivery

• 1 fabric softener dispenser

• Disconnect power before servicing the washer
• Pull the old dispenser straight up to remove; some models have tabs—release carefully
• Clean any buildup from the mounting area to prevent future clogs
• Press the new dispenser fully into place and ensure it sits level and secure

• Periodically remove and rinse the dispenser; dilute thick softeners per product directions to avoid clogs.

Color: black. Measures about 8 inches wide by 3 inches deep.

Used on the black and aluminum models

Color: Stainless

The Detergent Drawer is an OEM part for Whirlpool washing machines. This drawer holds and dispenses detergent, fabric softener, and bleach into the washer at the appropriate times during the wash cycle.  

Causes of a bad detergent drawer can include buildup of detergent residue, damage from overloading, or general wear and tear.

Symptoms of a bad detergent drawer include:

• Detergent not dispensing properly
• Drawer difficult to open or close
• Leaks from the detergent drawer area
• Visible cracks or damage

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This bleach dispenser for a washing machine holds liquid bleach and releases it into the tub at the appropriate point in the cycle, helping dilute bleach and protect fabrics from contact with undiluted solution. What it does:

• Holds and meters liquid bleach until the machine calls for dispensing
• Helps ensure bleach mixes with water for even, diluted distribution
• Replace if cracked, clogged, or leaking
• Common symptoms include bleach not dispensing, bleach left in the cup, leaks around the dispenser area, or bleach spots on fabrics

• 1 bleach dispenser

• Disconnect power and turn off water before servicing
• Access and mounting vary by model; follow your service manual to reach the dispenser
• Detach hoses/clamps or fasteners, transfer any reusable hardware, and seat the new dispenser fully
• Reconnect, then run a test fill/rinse to check for proper dispensing and leaks

Color: black. Measures about 9 inches wide by 2-1/2 inches deep.

This dishwasher detergent dispenser stores detergent and releases it at the correct time in the cycle for consistent cleaning results. Replacing a worn dispenser restores reliable dosing so each wash performs as designed. What it does:

• Holds detergent and keeps it contained until dispensing
• Opens the detergent cup door at the programmed time in the cycle
• Directs detergent into the wash stream for even distribution
• Helps prevent poor cleaning caused by early loss or failure to dispense

• 1 detergent dispenser assembly

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser; support wiring and insulation as you work
• Release mounting tabs/screws, transfer the wiring connector, seat the new dispenser evenly, and tighten fasteners uniformly
• Run a quick cycle to check for leaks

This yoke and pad assembly connects the dispenser auger motor to the ice bucket auger. Replacing a stripped yoke or worn pad restores torque transfer for smooth, reliable ice dispensing with reduced slipping and noise.

• Connects the auger motor shaft to the ice bucket auger
• Transfers drive torque through a cushioned pad to move ice out of the bin
• Helps reduce shock and slippage in the dispenser drive
• Common symptoms: ice won't dispense, auger doesn't turn, clicking/grinding during dispense

• Disconnect power and remove the ice bin to access the dispenser drive
• Support the auger motor to protect wiring; remove the retaining fastener and the old yoke/pad
• Install the new assembly on the motor shaft; align fully and tighten in the same orientation as the original
• Reassemble components, restore power, and test ice dispensing

This bleach dispenser stores liquid chlorine bleach and automatically dilutes and releases it at the correct point in the wash cycle. Replacing a cracked or clogged dispenser helps stop leaks, protect fabrics, and restore consistent bleaching performance.

• Holds bleach and siphons it into the tub at the proper time in the cycle
• Helps prevent undiluted bleach from contacting fabrics early
• Direct replacement for a dispenser that is cracked, warped, or clogged
• Address symptoms such as bleach remaining in the cup, dispensing too soon, leaks near the dispenser area, or fabric spotting

• Disconnect power and turn off water before servicing
• Access the dispenser through the top/console area; remove fasteners and detach connected hose(s)
• Transfer any hoses, clamps, and mounting hardware from the original part; ensure all connections are fully seated to prevent leaks
• Run a test/rinse cycle to check for leaks

This ice dispenser solenoid assembly engages the dispenser mechanism to switch between crushed and cubed ice. A worn or failed solenoid can prevent the selector from changing modes or stop ice from dispensing smoothly.

• Actuates the ice bucket/crusher selector to allow cubed or crushed ice
• Failure may cause only one ice option to work, no change between modes, or intermittent dispensing
• Can resolve loud clicking/buzzing from the dispenser area when switching options
• Helps restore proper ice dispensing performance

• Disconnect power before servicing the dispenser area
• Access is typically through the freezer door dispenser chute/ice bucket area
• Note actuator linkage orientation during removal to ensure correct reassembly
• After installation, test both crushed and cubed selections

This door-mounted dispenser stores detergent and rinse aid and releases them at the right time in the cycle to help deliver clean, spot-free dishes. Replace a broken, leaking, or jammed dispenser to restore proper detergent release.

• Holds detergent and rinse aid and dispenses them during the wash cycle
• Supports consistent cleaning performance by timing chemical release
• Detergent cup won't latch or open
• Rinse aid doesn't dispense or leaks from the dispenser
• Detergent remains in the cup after the cycle

• Disconnect power and turn off the water supply before servicing
• Remove the inner door panel to access the dispenser
• Disconnect the wire harness, release locking tabs/fasteners, and install the new unit flush to the door
• Clean the sealing surface; tighten fasteners evenly and run a test cycle to check for leaks and proper dispensing

This wax motor is the actuator for the dishwasher's rinse aid dispenser, releasing rinse agent at the correct time in the cycle. Replacing a weak or failed unit restores consistent rinse aid dispensing and helps minimize spotting.

• Actuates the rinse aid dispenser by extending a plunger when energized
• Works with the control to meter rinse aid during the final rinse
• Failure symptoms can include rinse aid not dispensing, the level never dropping, and increased spotting/filming on dishes
• Dispenser may remain closed with no audible actuation during the cycle

• Disconnect power at the breaker and shut off water before servicing
• Remove the door panel to access the dispenser; label and disconnect wires
• Release the old motor and install the new one in the same orientation, ensuring it seats fully
• Run a test cycle to ensure the dispenser releases rinse aid

This black dispenser grille fits at the base of the refrigerator's ice/water dispenser. It provides a clean, finished surface over the dispenser well and helps catch minor drips when the original grille is cracked, stained, loose, or missing.

• Sits over the dispenser well to catch minor drips and splashes
• Protects and finishes the dispenser recess for a tidy appearance
• Helps keep moisture away from surrounding door surfaces
• Typical failure signs: cracked, warped, discolored, broken tabs, or won't stay seated

• Disconnect power and shut off the water supply before servicing.
• Lift or slide the old grille out of the dispenser recess.
• Clean the area; align the new grille with the locating tabs.
• Press down until fully seated and flush with the surrounding trim.