Maytag Parts

• Lid or door won't close
• Lid or door will not open

I watched the AppliancePartsPros.com video on the part and replaced the hinge according to the video. Nothing could be easier. Read more

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

I googled the model number of the oven and came across AppliancePartsPros.com The coil along with replacing video was right at hand. I ordered the part, got it three days later (standard shipping) and installed it. To sum it up, it was a five minute job. Read more

• Spins slowly
• Pumps but will not spin
• Will not agitate

My Maytag washer make a loud screech when the washer tub needed to be stopped by the brake. Last year, I had replaced the suspension springs, the snubber ring, the drive belt and the drain pump. Those repairs worked fine, but a few weeks later, the screeching noise started. So I figured it was the brake system. I thought it would be better to replace the brake rotor and stator together as a set since I was going to disassemble both and they were 18 years old anyway. I decided to replace the... Read more

The rubber seal/gasket was torn on our KitchenAid refrigerator right side door. I purchased the replacement and followed the directions/recommendations of how to prepare the new gasket for installation. When it's removed from the shipping box, it does have wrinkles and preparing it is a must. I set it out on our tile floor and then used a heat gun (low setting) to warm it up and massage it. It took me about 15 minutes, stopping and restarting as I let the rubber come back to it's desired shape.... Read more

I ordered the water filter and when it came in I replaced the one in the fridge, held the button down for 3 seconds and the light went off. Read more

• Exhaust fan not working

Replacing this filter was very easy: two screws hold in the grill cover at the top of the microwave, and then the filter just slides in and out of its holder. There was quite a bit of grease in the area, probably pulled there by the vent from the stove top. I cleaned the grease up and also hand-washed the wire-mesh filter on the bottom of the microwave with soap and warm water. Airflow when running the vent is now noticeably better. Read more

Replace suspension rods. Read more

I checked repair videos on line. Put in my brand and model. You tube had a video how to dis assemble my model. Video made it really easy, I would never have figured it out. Now checked videos from Appliance Parts Pros to troubleshoot the fix. Checked all thermostats and fuses with ohm meter they checked out perfect. Finally checked the igniter found out I did not have resistance. I was also concerned I may need new coils (solenoids). In visiting with customer service he explained... Read more

I replaced the light fixture in 5 minutes. Been working well. Read more

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

Ordered new gaskets from Appliance Parts Pros, arrived in 4 days. Removed old gaskets and replaced by starting at top corner and. Pushing seal into slot. Day before, opened seal boxes and spread seals to smooth out. Took about 10 minutes to replace both door seals. Right door magnetic seal improved but not great. Adjusted level and installed a 1/16” washer in door bottom hinge, which leveled door better and improved the seal strength. Read more

My dryer was making a squealing noise when operated. In researching the fix, I came upon your website through Google. I found your videos for repairs very good. The videos also told me how well the Maytag dryer is engineered. I purchased some of the parts as preventive maintenance, such as the belt, and tumbler bearing kit. It was a good thing that I bought two felt seals when I did. Both were in terrible condition. I believe my rear felt seal was not installed properly when originally... Read more

First ran the built-in diagnostic tests. Got error code indicating that the inlet thermistor was open. Removed lower access panel and did continuity checks on the inlet thermistor, thermal cutoff and heating element. Even doing these checks is very difficult on this model due to the location of these parts and the limited access through the so-called access panel. But was able to get an open reading on the heating element, so I knew that at least that part was faulty. Could not get a reliable... Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

The replacement drawer arrived the day after I ordered it. I took the old drawer out, slid the new one in, and we were back in business. Read more

Replaced wheel assembly because prongs were broken and replaced track because wheel assemblies were rolling out from the track when extended. Read more