Maytag Parts

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

I had to cut the old agitator out with an oscillating saw in order to access the agitator drive. This is the second Maytag (MVWC 565) I have had to do this to. I first tried removing it by sliding straps under the agitator then then using a jack to pull it loose which did not work either time. One suggestion I have would be to remove debris from tub as you cut in order to prevent it from dropping from the inner tub into the outer tub. Read more

Ordered the correct part/ Pump from this Awesome website and replaced the drain pump. Good to go!! Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

Replaced the bellow. Read more

Ordered parts from Appliance Parts Pros. Made sure they fit using the model number link. Was a great experience, fast shipping. Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

• Burning smell

All's well that ends well, but the getting there was a bit of a pain. The web site suggests 3 possible causes for my problem (incl. the burning smell). I began with the first two since they were inexpensive compared to the motor, which was the third cause (and also the least often cause). There is no way to visibly tell if the motor is bad or not. After replacing the clutch assembly, which did have some plastic pins broken off) and the motor coupling (which actually looked fine, but the... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Little to no heat when baking
• Gas smell

Followed linked video instructions and replaced with new flat style Oven Igniter Kit. Some repair info background, while out shopping for a replacement oven ($1000 plus) a terrific salesman listened to the issue with my current oven and recalled his same issue and solution. I thanked him for his time and recommendation. I went home and searched "oven Ignitor" where I was led to this website. The video showed the same exact flat oven igniter and how easy it would be to replace it. I immediately... Read more

• Shakes and moves
• Noisy
• Pumps but will not spin

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

• Compactor ram gets stuck
• Noisy

The compactor failed with the ram down, so the drawer wouldn't open which in turn made the mounting brackets inaccessible. This necessitated sliding a thin oscillating saw blade between the cabinet face frame and the counter top to cut through the brackets. It was then possible to roll the unit out and place it on its side. I removed the five screws holding the bottom pan in place, dropped the pan exposing the gear/chain train. The large gear was cracked from shaft out to the edge. One of... Read more

I followed the very well made repair video for this particular part. The total time it took for the repair was under 20 minutes. But I have a suggestion for the repair video and that is to emphasize that when reinstalling boot. Have the tachnician point out that there are drain holes in the boot that need to be situated and reattached toward the bottom of the washer chassis. Unfortunately I had to redue and double the repair time because the wash water would not drain properly during wash... Read more

I ordered a new one. Got it much sooner than expected. Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

After taking the two vegetable drawers out from above, the glass shelf, the pantry drawer and the cross support for the glass, you can get to the two recessed hex head screws holding the end cap. You will need to transfer the metal drawer slide to the new cap, but it doesn't need to come off first. When the end cap is loose, gently rotate it toward the front. Once the humidity control slide is at 90 degrees from the back of the refrigerator, the tab holding it in place will slip out easily.... Read more

• Won't start
• Element will not heat
• Little to no heat when baking

I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more