Maytag Parts

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Little to no heat when baking
• Gas smell

Followed linked video instructions and replaced with new flat style Oven Igniter Kit. Some repair info background, while out shopping for a replacement oven ($1000 plus) a terrific salesman listened to the issue with my current oven and recalled his same issue and solution. I thanked him for his time and recommendation. I went home and searched "oven Ignitor" where I was led to this website. The video showed the same exact flat oven igniter and how easy it would be to replace it. I immediately... Read more

Ordered a new screen and filter. While waiting for arrival, removed wax covered dishes. Carefully removed wax filled filter and screen cover. Stuffed paper towels in hole to absorb water and prevent wax from entering pump. Prayed ????wax had not entered pump. With plastic knife removed visible wax. Wiped out with paper towels. Used entire roll. Used hair dryer to melt remaining wax and wiped every inch of racks, wheels, glides, silverware holder, seal, floor and so forth. Oh yes I did. At 1:30... Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

After taking the two vegetable drawers out from above, the glass shelf, the pantry drawer and the cross support for the glass, you can get to the two recessed hex head screws holding the end cap. You will need to transfer the metal drawer slide to the new cap, but it doesn't need to come off first. When the end cap is loose, gently rotate it toward the front. Once the humidity control slide is at 90 degrees from the back of the refrigerator, the tab holding it in place will slip out easily.... Read more

• Won't start
• Element will not heat
• Little to no heat when baking

I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more

• Leaking

I thought it was the gasket so I ordered a new one. While waiting for it to arrive I read some other forums where I read that sometimes the air vent on the front could be dirty and cause leaking. I popped out that vent cover and it was clogged. Using an old toothbrush and a tiny paint brush I cleaned all of the gunk out. No more leak even with the old gasket in place. I'll save the new gasket for when I need it in the future. Read more

I researched the correct part I needed and ordered it. The part arrived in only 2 days. Installation was easy and the refrigerator is like new again. Read more

I determined that the gasket was pinched, leaking at corner. Ordered new gasket from this site (easy find with part diagram). Removed old gasket, replaced with new. Read more

• Ice maker dispenses too much ice

Ice Door Kit, Control Bracket, and Ice Dispenser Guide were purchased. I followed two videos on replacing the parts. The Control Bracket WP2180226 / AP6005965, was straight forward and I discovered a snapped pin on the old bracket causing an electric switch to be out of place... that repair was easy. When it came to the hinges of the ice chute, I discovered the snap-in, on right side, of the hinge was cracked... this is why the pin escaped. This cracked part is molded into the entire... Read more

Appliance parts Pros .com sent the part the day after the order . It was a genuine whirlpool part that was securely wrapped for shipment . I opened the package and installed it in less than five minutes . Read more

We watched a "youtube" video on how to fix a fridge door seal and even though this particular model fridge was not the same...it helped to see how to fix it. It took me 20 minutes to remove and replace the new door seal. The part ordered was ordered and delivered next day which was great!! Read more

I went to the local Home Depot and Lowes, but they did not have the parts because they do not carry parts for the items they actually sell to people. Jumped on the phone and did a quick search for parts and came across appliancepartspros.com. I put in the make and model of my dryer and all the parts for the dryer where listed. I ordered the items on a Wednesday night. I opted for the two day shipping. I thought the items would be at my house by Friday but they did not arrive until Monday. I... Read more

Ordered quality bags for compactor easily, and delivery to door was quick. Read more

• Fridge runs too long
• Noisy
• Freezer section too warm
• Fridge too warm

After reviewing the 'how to' video on AppliancePartsPros.com, I unplugged the refrigerator and removed the back cover to access the motor. I then unplugged the wiring and removed the bad motor. I cut the clip plug and wired it to the new motor, installed the fan blade from the old motor and re-installed the new motor. After connecting the clip plug and re-installing the back cover, I plugged the refrigerator in and checked the interior about 5 minutes after the repair. Everything has been... Read more

Pulled the washer apart (using your videos as a refresher) and found that the plastic coupling between the motor and the transmission had failed. Searched for parts vendors and found your site. Ordered the coupling on-line and went back down to clean up the machine. In the cleaning process I found a damaged thrust washer for the upper agitator and broken drive dogs for that same agitator. I went to the website to see if I could augment my initial order. I did not want to pay shipping costs... Read more

Replaced the water line and water supply solenoid valve (slight weeping at valve body also). This is a 3 year old whirlpool refrigerator, model WRX988SIBM00. A crack in the water line after only 3 years is a poor design. My intent was to replace the entire water line from the valve to the filter. But I could not remove the interior top trim piece to access the filter connection. I did not want to force the trim piece to hard and break it. So what I did was install a new water line at the... Read more