Maytag Parts

Yes exact fit Read more

I bumped into my KitchenAid dishwasher and the upper rack adjuster cracked. There was already a crack on the notch of the housing where the handle (lever) sits. In addition, the positioner popped out and I couldn't find it. So, I bought the three parts from AppliancePartsPros online. It arrived in about a week. The repair was fairly simple, but it still took about 45 minutes because I didn't want to crack the assemblies. For the housing, use a small slotted screwdriver to carefully... Read more

Watched a quick YouTube video. Read more

An appliance repair man in area did repairs, the screws were not easy to find and none were supplied with baffles! Read more

I am 72 years old. I appreciate my dishwasher, especially during the Holidays when we have lots of company. The bottom spray arm in my Amana dishwasher was not snapped into place and it ended up on the heating element...needless to say, it fried two holes in the spray arm and from that day on, it did not function as planned. I ordered the part from AppliancePartsPro.com and the new arm arrived as promised. It was well packaged and a perfect fit. I am so pleased and I know when I need parts... Read more

Order parts and replace. When removing attachments, do them one at a time and install them on new rack as you go. Watch for the small release tabs on the attachments (baskets, rollers and tine holders), "gently" put pressure to release; remember these units have been in hot water and they are brittle. Read more

I called a repairman and he wanted $230 to put in a new timer so I went online to Appliance Parts Pros.com and found the part and watched video on how to replace timer. The timer cost $89 and I received it in 2 days. It took about 3 minutes to replace and my dryer works great! Read more

Steam vent baffle had failed and was not fully closing. Bottom seal also crusted with hard water deposits, and mildew on door insulation from leak. Replaced vent assembly, new insulation after cleanup, new bottom seal after cleanup. Read more

I ordered a new motor with a very helpful Chris.It arrived a day later with instructions and was easy to exchange with the old one.I am delighted with how it works and the price was good and the service excellent.thank you. Read more

• Element will not heat

Followed the instructions that came with the replacement part: made sure stove top was unpowered, unscrewed the old housing from the stove top, cut the wires, stripped some insulation off, attached the new wires with the (accompanying) wire nuts, attached new housing to stove top. Read more

Rebalanced the load but noticed the drum was sitting lower and the springs were wore out and it went out of balance easy, so i got the suspension rod kit and installed it and it works much better. It took me 2 hours because i didnt have adequate room to move around. Hour job if you have room. Read more

I ordered parts from appliance parts pro at 3:30 on Friday and they were delivered at bout noon on Saturday the next day. Took the machine apart removed the old pads. With the directions in the packages put it back together and the wife ran 5 loads of clothes through it. Works great. Was awesome to get the parts so quick Read more

Ordered from an appliance store and got wrong bulbs. They wanted to charge $15.00 each for the right ones. Your sight had then for $7.00. Read more

Put in new LED lighrt module you sent me Read more

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

• Element will not heat

Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more