Maytag Parts

• Element will not heat

Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,... Read more

• Leaking

Luckily we planned ahead when building the laundry room, as we built a water catch basin and drain under the washer, but waking up to see 1-2 inches of water is never a good sign - even if it is contained. It appears that a sleeve of a shirt was accidentally caught between the door mechanism and the bellow seal. After a few hundred revolutions in the washer, the shirt knotted up and was torn free of its pinch - in doing so, it tore a quarter sized hole in the rubber bellow seal. This was,... Read more

Remove upper and lower baskets for access. Remove 4 Torx screws holding drain/filter assembly, accessing last screw by rotating the water duct clockwise. Be sure to first un-clip the water duct at top and rear of dishwasher so that it can be moved. (Take the opportunity to remove accumulated deposits behind the water duct). Remove the drain/filter assembly and then remove the single screw holding the food chopper housing. Then remove the chopper assembly which is likely to be in pieces if it... Read more

I bumped into my KitchenAid dishwasher and the upper rack adjuster cracked. There was already a crack on the notch of the housing where the handle (lever) sits. In addition, the positioner popped out and I couldn't find it. So, I bought the three parts from AppliancePartsPros online. It arrived in about a week. The repair was fairly simple, but it still took about 45 minutes because I didn't want to crack the assemblies. For the housing, use a small slotted screwdriver to carefully... Read more

• Will not fill with water

As mentioned, our Whirlpool Dishwasher would complete the cycle but Tablet pretty much sat in the Soap Dispenser Box nor there was any sign of water inside the Dishwasher. This happened 2 - 3 times. Hence decided to dive into what the fix was. After reviewing a bunch of Youtube Videos, understood first how a typical Dishwasher operates and what are the basic checks it does before water is let inside. So it typically first checks whether Door S/w got activated, followed by Float Switch... Read more

I replaced the gearcase and hub. With the help on line videos the process was straight forward and simple. Read more

• Frost buildup
• Leaking

The drain tube for for the defrost cycle seemed to be blocked, so I googled the repair & it sent me to AppliancePartsPros. Obviously, there's a design problem with this model since many other people have the same issue. This tube is an upgrade on the original for my KitchenAid model (design flaw). Since installation 4 days ago, I have had no leaks - awesome! The video for installation of the new tube on AppliancePartsPros was excellent. Two additions to the video: 1) I used a hair dryer... Read more

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

I began by turning off the breaker. I then removed the screws securing the bake element. I immediately noticed only one side was wired and the other side was burned off. The wire for the burned off section had fallen through the hole in the back of the oven. I tried fishing it out to no avail. I removed two side trim screws, the side trim pieces, and two screws holding the built-in oven into the wall. I was able to slide the oven out and onto a square stool that was the correct height. I... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Gas smell
• Little to no heat when baking

I used the little video clip shown under the part and replaced it myself. Read more

Ordered numerous replacement parts. Started with the tracks which required pulling the washer out of the cabinet to reach the screws. Pushed it back in and re-secured. Then stared on the rack and replaced the rack adjusters and various clips. Everything is straight forward and easy to replace. I originally called a local repair place to have them repair it. They came out and said they needed to order parts and they would call back. A week went by and I followed up with them. Had to leave... Read more

Ordered numerous replacement parts. Started with the tracks which required pulling the washer out of the cabinet to reach the screws. Pushed it back in and re-secured. Then stared on the rack and replaced the rack adjusters and various clips. Everything is straight forward and easy to replace. I originally called a local repair place to have them repair it. They came out and said they needed to order parts and they would call back. A week went by and I followed up with them. Had to leave... Read more

Door gasket was easy to remove and reinstall. Original gasket was penetrated while cleaning food stuff from folds in the seal below the frig doors. (Gasket is very fragile so don't try to expand the folds while cleaning. I used my finger and a paper towel but in hindsight should have used a Q-Tip. Also, when installing the new gasket you have to be sure the seam folds over the edge of the door and doesn't get caught underneath. Read more

We bought a new filter. Read more

• Noisy

After ignoring for a couple of years that the bearings were bad on our Whirlpool Cabrio washer and just closing the door to the laundry room, it started slinging grease underneath during the spin cycle. Knowing that the cost to call out a repairman would be close to the cost of a new washer, I decided that it would be a nice Saturday project after reviewing AppliancePartsPros’ repair video. The bearing & tub seal kit and bearing installation tool arrived in two days. I’ve done a lot of... Read more

After looking up the model number of my washing machine on AppliancePartsPros.com I ordered the suspension rod kit, two sets of tub centering springs (one spring per corner), a Ring-Tub (mine was breaking apart due to banging around) and a spare suspension bearing kit in case I need it later. I spoke to a very helpful customer service rep on the phone just before placing my order. They have customer service representatives answering the phone late at night. I was surprised. All of my parts were... Read more

• No heat or not enough heat

I replaced the "heating element" which was bad.........as well as the "Thermst-fix" and "Thermal Cutoff" which are located on the side of the element mounting location while I had the dyer all opened up and the element mounting tube removed.......I also replaced the Dryer Thermister which is located on the top of the blower fan.....To get to these parts, you must open the top of the dryer which has spring latches on both sides of the front corners... they need to be pressed in (use a putty... Read more