Maytag Valve

The Water Inlet Valve is an OEM part for Whirlpool side-by-side refrigerators with internal water and ice systems. Located behind the rear panel on the water supply line, it controls water flow into the refrigerator.

Symptoms of a faulty inlet valve include:

• Slow or incomplete fills of the ice maker or water dispenser  
• Intermittent water flow or pressure issues at the dispenser
• Water leaks from around the inlet valve housing 

Causes can be mineral buildup on internal valve parts restricting flow after years of use. Mechanical wear and cracks in the plastic casting may also develop over time.

This OEM replacement is compatible with additional Whirlpool, KitchenAid, and some Kenmore side-by-side refrigerator models.

The Valve is an OEM part for Whirlpool refrigerators. This valve controls the flow of water into the ice maker and water dispenser, ensuring the proper operation of these features.

Causes of a bad fridge valve can include wear and tear over time, mineral deposits clogging the valve, electrical malfunctions, or damage from freezing. Regular use can also lead to the degradation of internal components, impacting the valve's functionality.

Symptoms of a bad valve include:

• Water dispenser not working
• Ice maker not producing ice
• Leaks or water pooling around the valve
• Unusual noises during water dispensing

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Single Water Valve is an OEM part for Whirlpool refrigerators. This valve controls the flow of water to the refrigerator’s ice maker and water dispenser, ensuring a consistent and reliable supply of water for ice production and dispensing.

Causes of a bad single water valve can include wear and tear over time, mineral buildup from hard water, or electrical malfunctions. 

Symptoms of a bad single water valve include:

• No water dispensing from the refrigerator
• The ice maker not producing ice
• Leaks around the valve area
• Unusual noises when the water dispenser is activated

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Water Inlet Valve Assembly is an OEM replacement part for Whirlpool washing machines. It is responsible for controlling the flow of water into the washer during fill cycles. A faulty valve assembly can cause issues such as abnormal sounds, reduced or no water flow, or leaks.

Symptoms of a bad water inlet valve include:

• The washer not filling or partially filling with water
• Odd noises coming from the valve area during fill cycles  
• Water continuously running into the washer even when not in use
• Leaks around or below the valve area

Causes of a bad water inlet valve can include mineral buildup restricting water flow, worn internal components allowing unintended water passage, or damage from fluctuations in water pressure over time.

Note: If hose clamps are rusted order 4 of WP285655.

This OEM part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 
 

This water inlet valve regulates the flow of household water into the dishwasher at the start of each cycle. Replacing a weak, clogged, or leaking valve restores proper fill level for reliable performance and helps prevent leaks or fill errors.

• Opens to allow the correct amount of water into the tub; closes to stop the fill
• Common fix for dishwasher not filling or taking too long to fill
• Can resolve low water level that leads to poor cleaning results
• May stop water from seeping into the tub when the dishwasher is off
• Replace if the valve body leaks or the inlet screen is damaged/clogged

• Disconnect power and turn off the dishwasher's water supply before servicing
• Access the valve behind the lower toe/kick panel; place a towel to catch residual water
• Note wire and hose positions and move them to the new valve one-for-one
• Restore water and power, then run a fill to check for leaks and proper operation

This water inlet valve controls the flow of household water into the refrigerator system. Replacing a failing valve restores reliable water supply for functions like ice making and dispensing.

• Opens and closes to allow water into the refrigerator as commanded
• Common failure signs: no ice production, slow or no water from dispenser, intermittent fill, or leaks at the valve area
• May cause humming from the valve when energized but not filling

• Unplug refrigerator and shut off the water supply before starting
• Have a towel ready to catch any residual water
• Transfer any mounting hardware or fittings from the old valve if reused
• After installation, restore water and power, then check all connections for leaks

This water inlet valve kit restores proper water flow to your refrigerator's ice maker and/or dispenser. Replace a sticking, leaking, or failed valve to resolve no-ice, no-dispense, or slow-fill issues and help prevent water leaks.

• Controls water from the household supply to the ice maker and/or water dispenser on demand
• Opens when energized and closes to seal off flow when inactive
• Common symptoms include no ice production, no or slow water dispensing, dripping at the fill area, leaks near the valve, or unusual buzzing/clicking from the valve
• Helps maintain consistent, reliable filling performance

• Unplug the refrigerator and shut off the water supply before servicing
• Place a towel or container to catch residual water and relieve line pressure
• Note tube and wire locations; transfer bracket/fittings as needed and tighten all connections securely
• Restore water and power, check carefully for leaks, and purge air from the system per manufacturer guidance

This smart electronic water inlet valve controls the flow of fresh water into the dishwasher during each cycle. Replacing a weak, leaking, or stuck valve restores proper fill performance and helps prevent no-fill, slow-fill, or unintended filling. What it does:

• Opens and closes under control of the electronic board to admit water at the correct time
• Regulates incoming water so the tub fills to the proper level for each cycle
• Failure symptoms can include no fill or very slow filling
• May allow water to seep into the tub when off, or leak from the valve body/fittings

• 1 water inlet valve assembly

• Disconnect power and turn off the water supply before servicing
• Place a towel or tray to catch residual water; depressurize the supply line
• Move the wiring connectors one at a time to the new valve to avoid miswiring
• Restore water and check all connections for leaks; run a fill test to verify operation

This overfill control float sits in the dishwasher tub and rises with the water level to signal the float switch to stop filling. Replacing a cracked or sticking float helps prevent leaks and recurring fill issues. What it does:

• Rises with the water level to actuate the float switch and stop the inlet valve
• Helps prevent overfilling and water leaking from the door
• A float stuck in the UP position can cause no fill or short fill
• A float stuck DOWN or damaged can allow overfilling

• 1 overfill control float

• Disconnect power and turn off water before servicing
• Remove the lower rack; lift out the old float from its guide and clear any debris in the well
• Insert the new float, ensuring it moves freely and reliably actuates the switch when raised

This water inlet valve regulates the flow of household water into the dishwasher during each fill. Replacing a worn or clogged valve restores proper filling and consistent wash performance while helping prevent long fill errors. What it does:

• Electrically opens and closes to allow the correct amount of water into the tub.
• Maintains proper water level for wash and rinse phases.
• Common failure symptoms: no water entering, slow/low fill, long fill or "faucet"/fill errors, or leakage from the valve body.
• Internal screen can clog with debris, restricting flow.

• Disconnect power and turn off the water supply before servicing.
• Access the valve near the front/bottom of the dishwasher; place a towel or pan to catch residual water.
• Move wires and water connections one at a time; transfer any mounting hardware or fittings from the original valve as needed.
• Restore water and power, check for leaks, and run a test fill; ensure the float/float switch moves freely.

This water inlet valve regulates the flow of household water into the appliance. When the control energizes the solenoid, it opens to deliver the correct amount of water for filling and operation, restoring proper flow and performance.

• Controls on/off flow from the household water supply
• Opens when signaled to provide the correct amount of water for fill functions
• Helps maintain consistent water flow to the system
• Common failure symptoms: no water flow, slow fill, intermittent filling, or leaking at the valve body

• Disconnect power and turn off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Note tubing and wire locations before removal; transfer any brackets or clips as needed
• After installation, restore water and power, check for leaks, and purge air from the lines

This float controls your dishwasher's water level. As the tub fills, it rises to signal the float switch to shut off incoming water, helping prevent overfilling and leaks.

• Lifts with the water to actuate the float switch and stop filling
• Helps protect against overfilling and door leaks
• Replace if the float is cracked, deformed, waterlogged, or sticks in its well
• Symptoms can include: won't fill or stops filling early; overfilling or leaks at the door

• Disconnect power and shut off the water supply before servicing
• Remove the lower rack and locate the float in the tub floor
• Lift the old float straight up; clear any debris; seat the new float and free up-and-down movement
• Restore power and run a fill test to proper operation and check for leaks

This water inlet valve assembly controls the flow of water from the home supply into the refrigerator. Replacing a faulty valve restores proper water delivery to the ice maker and/or dispenser for consistent ice production and dispensing.

• Opens and closes to send water to the ice maker and/or dispenser as commanded by the refrigerator
• Common symptoms: no water from dispenser, no ice production, slow/weak dispenser flow
• May also present as continuous dripping into the ice maker/dispenser or leaks around the valve body
• If water lines and filter are clear but filling is inconsistent or absent, the valve may be at fault

• Disconnect power and shut off the water supply before servicing
• Place a towel or shallow pan to catch residual water; note line and wire locations for reassembly
• Ensure tubing is fully seated in fittings; avoid overtightening plastic connections
• Restore water and power, then check all joints for leaks and run the dispenser to purge air/debris

This water inlet valve assembly regulates when and how much water enters the appliance. Replacing a failing valve restores proper filling or water delivery and helps resolve no-water, slow-fill, or drip-through-the-valve issues.

• Opens and closes to control incoming water flow as commanded by the control system
• Directs water to the appliance's water circuit for proper operation
• Common symptoms: no water entering, weak/slow flow, water seeping in when off
• Physical clues: cracked housing, mineral buildup, or a valve that hums but doesn't pass water

• Disconnect power and shut off the water supply before servicing
• Keep towels handy; relieve line pressure before disconnecting tubing/fittings
• Transfer connectors and any mounting hardware one-for-one; ensure tubing is fully seated and use appropriate thread sealant if your model uses threaded fittings
• Restore water, check all joints for leaks, then restore power and run a test cycle

This vacuum break is the washer's water-inlet anti-siphon fitting. It maintains a required air gap so the tub fills properly without drawing used water back into the supply, helping prevent leaks and backflow issues.

• Maintains an air gap at the inlet to prevent backflow/siphoning into household water lines
• Helps ensure consistent, unobstructed water flow into the tub
• Replaces a cracked, clogged, or leaking vacuum break at the fill area
• Common symptoms include leaks from the rear/top during fill, visible cracks, or restricted/noisy fill

• Unplug the appliance and shut off both water supplies before servicing
• Access the fill/inlet area; note hose routing and part orientation
• Remove hose clamps/hoses and the old vacuum break; install the new part and secure clamps
• Restore water and power, then run a fill test and check carefully for leaks

Water inlet valve kit replaces older valves that used the "Y" type water lines.