Maytag Valve

This mixing valve bracket secures the washer's water inlet valve to the cabinet, keeping the valve steady and properly aligned for hose connections. A correct-fit bracket helps reduce rattles and potential leaks caused by a loose valve.

• Mounts and supports the water inlet/mixing valve on the rear panel
• Maintains proper alignment for hot and cold supply connections
• Helps reduce vibration and rattling noises during fill
• Common signs it's needed: loose or dangling valve, misaligned hose connections, or leaks at the valve fittings

• Disconnect power and turn off both water supplies; relieve pressure before removing hoses
• Access the rear of the washer and remove fasteners securing the existing bracket/valve
• Transfer the valve to the new bracket, reusing the original hardware
• Reattach the bracket to the cabinet, reconnect hoses, restore power and water, then check for leaks

This replacement housing is the molded support/cover used in select appliances to secure and protect its mated components. It restores proper alignment and sealing when the original housing is cracked, warped, or has broken mounting tabs. What it does

• Provides a rigid mount and enclosure for the associated component(s)
• Maintains correct alignment and sealing to prevent leaks or air loss
• Protects internal parts from damage and vibration
• Common failure signs: visible cracks, broken tabs, rattling, poor fit, or leakage around the assembly

• Housing

• Disconnect power before servicing; if the part interfaces with water, shut off the water supply
• Note orientation and transfer any screws, clips, seals, or O-rings from the original part
• Inspect mating seals and fittings; replace any worn gaskets to ensure a proper seal
• After reassembly, restore power/water and test for proper operation and any leaks or noise

This water inlet valve regulates the flow of household water into the refrigerator for ice making and dispensing. Replacing a failing valve restores proper fill and helps resolve leaks, low flow, and no-ice/no-dispense issues. What it does:

• Opens and closes to supply water to the ice maker and/or dispenser when energized by the control
• Addresses symptoms like no water at the dispenser, no ice production, slow fill/hollow cubes, or dripping/leaks at the valve area
• Common failures include stuck or leaking valve, clogged screen, or a failed solenoid coil
• Helps eliminate valve buzzing with no fill when the coil is energized but the valve won't open

• 1 water inlet valve assembly

• Disconnect power and shut off the water supply before servicing
• Keep towels/containers handy; some residual water will drain when lines are removed
• Note and label each tube and wire position; transfer any fittings/brackets from the old valve if applicable
• After installation, restore water and power, check all connections for leaks, and purge air by dispensing water

This electrically actuated valve controls the flow of household water into your appliance during operation. Replacing a sticking or leaking valve restores proper fill performance and helps prevent unwanted dripping between cycles. What it does:

• Opens and closes to admit the correct amount of water at the right time
• Helps maintain stable water pressure and shutoff to the unit
• Common symptoms of a failing valve: no fill, slow/insufficient fill, water seeping into the tub when off, or leaks from the valve body
• May buzz or hum without allowing water flow when the internal coil or screen has failed or is clogged

• 1 water inlet valve

• Disconnect power and shut off the water supply before servicing
• Keep towels or a tray handy; some residual water will drain
• Note hose and wire orientations; transfer any brackets or fittings from the original valve
• After installation, restore water and power, check for leaks, and run a test fill cycle

This water inlet valve controls the flow of household water into the dishwasher at the start of a cycle. Replacing a weak, stuck, or leaking valve restores proper filling performance and helps prevent fill-related errors and leaks. What it does:

• Opens and closes electrically to regulate water entering the dishwasher
• Helps ensure correct fill level and timing for each cycle
• Common failure symptoms: won't fill or slow fill, water seeping into tub when off, external leak at valve connections, loud buzzing/chattering during fill
• May set fill or water supply-related error codes on some models

• 1 water inlet valve assembly

• Disconnect power and turn off the water supply before servicing
• Have a towel or shallow pan ready for residual water when removing lines
• Transfer any original mounting hardware or fittings from the old valve as needed
• Inspect/clean the inlet screen and flush the supply line; check all connections for leaks after installation

This overfill float and shaft assembly monitors the dishwasher's water level. As the tub fills, the float rises and triggers the float switch to shut off the inlet water, helping prevent overfilling and leaks.

• Senses tub water level and moves up/down with the water
• Activates the float switch to stop filling at the correct level
• Helps protect against overfill-related leaks
• Common symptoms include: won't fill (float stuck up), continuous filling/overfilling (float stuck down or damaged), or float not moving freely

• Disconnect power and turn off the water supply before servicing
• Lift the old float straight up from inside the tub; access the underside (behind the toe panel) as needed to release the shaft from the float switch lever
• Install the new shaft through the guide and onto the switch lever; seat the float so it moves freely
• Verify smooth float movement and test a fill cycle while checking for leaks

The Washing Machine Water Inlet Valve is an OEM part for Whirlpool brand washing machines. It regulates water flow into the washer tub during fill cycles and shuts off the supply automatically when the proper water level is reached.

Causes of a bad inlet valve include mineral buildup inside the valve filter restricting flow over time, or mechanical failures of internal plastic parts like diaphragms and seals due to usage stress.

Symptoms of a bad water inlet valve include:

• Slow or inconsistent filling during wash cycles  
• Water failing to shut off fully after the designated fill level  
• An inability to properly meter incoming water supply amounts
• Water leaks noticed beneath or around the valve area

This OEM replacement valve ensures precise water flow regulation. Compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models.

This valve controls the flow of household water into the dishwasher during the fill portions of the cycle. Replacing a weak, stuck, or leaking valve restores proper filling and helps prevent fill errors and water damage. What it does:

• Opens and closes to let the correct amount of water into the tub
• Common symptoms: no fill or very slow fill
• Water entering the tub when the dishwasher is off or won't stop filling
• Drips or leaks from the valve body or hose connection

• One water inlet valve assembly

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water; relieve line pressure at the supply
• Note wire and hose orientation before removal; move connections one at a time
• After installation, restore water and power, then run a brief fill to check for leaks

Included with nut.

Includes water inlet valve, vacuum break, wire harness and connector hose.

This overfill control float assembly sits in the dishwasher tub and rises with the water level. It works with the float switch to shut off the inlet valve, helping prevent overfilling and potential leaks.

• Rises with the water level to engage the float switch and stop water flow
• Helps protect against tub overfill and floor leaks during the fill cycle
• Replace if the float is missing, warped, stuck, or doesn't move freely
• Symptoms can include continuous filling/overfilling, water spilling from the door, or no fill if the float is stuck in the up position

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; lift the old float straight up from the tub opening
• Clear any debris from the float well so the new float moves freely
• After reassembly, start a fill to ensure the float rises and water shuts off

This vacuum break valve (also called a vacuum breaker or anti-siphon valve) prevents dirty water from being drawn back into the supply when flow stops, protecting your water supply and helping maintain proper fill and drain performance.

• Breaks siphon/backflow after fill or drain cycles to prevent contamination
• Helps maintain correct water levels and consistent filling
• Common symptoms of a failed valve: leaks at the valve/hoses, unintended draining or backfilling, intermittent or slow fill, gurgling noises
• Restores the proper water flow path when replaced

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when removing hoses
• Note hose orientation and transfer existing fittings/clamps as needed
• Restore water/power and run a test cycle; check carefully for leaks

This surface burner valve controls gas flow to a cooktop or range burner for smooth ignition and precise flame adjustment. Replacing a worn valve restores reliable lighting and consistent simmer-to-high control at the knob. What it does:

• Regulates and meters gas flow to a surface burner from Off through all heat settings
• Wear or blockage can cause no ignition, hard-to-turn knob, or poor/unstable flame
• Helps correct burners that won't adjust properly or won't stay lit
• Ensures safer, consistent burner performance when operating correctly

• 1 surface burner valve

• Disconnect power and shut off gas supply before servicing; allow appliance to cool
• Work in a well-ventilated area and follow local codes
• Note knob orientation; transfer any orifice fittings or mounting hardware from the old valve
• After installation, check all connections for leaks using a non-corrosive leak-detection solution

New seals come with this valve.

This gas valve controls the flow of gas to a burner, enabling safe ignition and precise flame adjustment. Replacing a worn valve restores smooth knob operation and consistent flame performance on your gas cooking appliance.

• Opens and closes to start/stop gas flow to a specific burner
• Works with the control knob to modulate flame size
• Helpful when a burner won't light despite spark/ignition present
• Can address issues like inconsistent flame or a knob that's hard to turn

• Disconnect power and shut off the gas supply before servicing
• Match the orientation and connections to the original valve
• Use an approved gas-rated thread sealant on threaded fittings
• After installation, check all joints for leaks with a soap-and-water solution

This water valve kit regulates the flow of hot and cold water into your appliance during fill. Replace a weak, leaking, or stuck valve to restore consistent fills and proper shutoff, resolving common no-fill, slow-fill, or seeping issues.

• Controls incoming water to achieve correct fill levels and temperature mix
• Addresses no fill, slow/partial fill, or water seeping into the tub when off
• Replaces valves that are electrically failed or mechanically clogged/sticking

• Disconnect power and shut off both water supplies before servicing
• Have towels ready; relieve hose pressure and note wire/hose locations (take a photo)
• Transfer any mounting parts from the original valve if required; avoid overtightening plastic fittings
• Restore water slowly, check for leaks, and run a test fill