Refrigerator Dispenser Parts

Since I don't have all the tools or skills to properly diagnose an issue, i often employ the "trial and error" method. My logic is that the part probably needed to be replaced anyway. Originally thought it to the be the water valve (which turned out to be an easy repair). After attempt #1 did not solve the complete problem (less water accumulating, but still some water accumulating) I emailed a question late Sunday evening to the 24/7 hotline, and they suggested the proper solution and... Read more

Once the parts arrived, I followed the help video that was emailed to me with my order confirmation step by step. Super useful! The video quality and editing were well done and the instructions were very specific. I felt like a pro! Read more

Even though the refrigerator is 13 years old, I was able to find replacement parts on your site. The DIY video provided on-line for each of the four parts ordered was very helpful ; even though my refrigerator wasn't exactly like the one in the video, it was still helpful. I'm not usually the DIY type- but with your help the repair was very successful! Thank you ! Read more

Bought OEM replacement part. The new part had all the retaining clips that had broken off of old part. Needed new stick-on label to dress up the replacement shroud. Hardest part of the repair was disconnecting the wired module on back of old shroud. Feared I might snap off those retaining clips, too! Best part of experience of AppliancePartsPros.com was the help received to confirm parts ordered were grey to match the original install on stainless steel Frigidaire. Read more

The tray just sits in a slot on the door so no tools required Read more

Ordered part, it fit perfectly! Read more

I replaced the Ice Dispenser Lever. Since the replacement part is only available in white and my fridge is bone, I replaced also the Water Dispenser Lever, so it looks much better. I followed the instructions in the video, which were very useful and very well done. My problem was that the refrigerator is a KitchenAid built-in, while the instructions were for a Whirlpool, so the removal of the faceplate was quite different from what was shown in the video and more difficult. Also there were some... Read more

Replaced with ordered cover and new screws. Cover was a perfect replacement for original. Replacement took less than 15 minutes to complete. Read more

Flipped the circuit breaker to turn the power to the fridge off. Had to remove the faceplate to the ice/water dispenser. Had to remove approx 16 screws and unplug the circuit board. Removed water tube (That was the hardest part) ! Had to disconnect and remove the broken part and reattach the new part. Then put everything back together again. Read more

Super easy fix, remove two screws behind drop tray, unplug the wiring harness to dispenser, unplug and remove old pad, then snap new one into place. Reconnect harness. Took less than 5 minutes, works like new. Read more

Even though the refrigerator is 13 years old, I was able to find replacement parts on your site. The DIY video provided on-line for each of the four parts ordered was very helpful ; even though my refrigerator wasn't exactly like the one in the video, it was still helpful. I'm not usually the DIY type- but with your help the repair was very successful! Thank you ! Read more

After using the crushed ice feature on my KitchenAid French Door refrigerator, the ice maker wouldn't stop dispensing ice, crushed or cubed. I thought it had to do with the paddle switch being stuck or something else in the door, but all door components seemed to be working as intended. I ended up pulling the ice maker out and disconnecting the wires to the auger so that I could leave the refrigerator plugged in. I call AppliancePartsPros.com the following morning and explained my situation.... Read more

I removed the old one and put the new one in. It took about 1 minute. That is because I am counting the time it took from opening the package, removing the old dip tray and replace it with the new one Read more

All parts arrived in a timely matter, all parts fit as expected, easy fix Read more

Removed water catcher, then 4 screws in water/ice vault in door, then removed screws on door side (5) top (2) and bottom (2). Removed stainless door skin. Removed 4 hex head bolts in ice/water vault (containing pads) and 4 bolts on the module immediately above the vault. Pulled the vault and module above out part way to unplug one cable. Then laid on table to unplug pads. From back, each pad has a small indent preventing the pad from being pushed up and removed. Push the small indent with a... Read more

REPLACED WITH YOUR MODULE. ARRIVED AS PROMISED & SAME AS OLD ONE. THANKS Read more