Refrigerator Temperature Control, Cold Control

This defrost thermostat senses evaporator temperature and shuts off the defrost heater once the coil warms, preventing overheating. Replacing a failed thermostat restores proper defrosting to stop ice buildup and stabilize refrigerator temperatures.

• Controls the defrost heater based on evaporator coil temperature
• Closes when cold to allow defrost; opens as the coil warms to end the cycle
• Protects against overheating during defrost
• Failure may cause frost/ice on the back wall or evaporator, poor cooling, or a heater that never energizes

• Disconnect power before service; evaporator fins and sheet metal are sharp
• Access the evaporator by removing the freezer rear panel; note wire routing and mounting
• Position the new thermostat in the same location for tight contact with the tubing; reconnect wires exactly as found
• Reassemble and monitor a defrost cycle to confirm heater operation

This mechanical temperature control thermostat regulates your unit's cooling by cycling the compressor on and off to maintain the set temperature. Replace a failed cold control when temperatures drift, cycling is erratic, or the knob no longer responds.

• Monitors cabinet temperature via a sensing bulb and opens/closes electrical contacts to control cooling
• Helps restore consistent temperatures and normal run times
• Typical failure symptoms: too warm or too cold, runs constantly or won't start, no change when adjusting the control
• May cause intermittent cooling or short cycling as it wears

• Disconnect power before servicing
• Access the control housing; note/photograph wire locations and transfer them one at a time
• Route the sensing capillary exactly as original; do not kink or sharply bend the tube; secure the bulb in its original location
• Set the control to a mid setting and allow temperatures to stabilize before fine-tuning

This thermostat assembly senses refrigerator temperature and signals the compressor and fans to maintain set cooling. Replacing a failed thermostat restores temperature regulation for more consistent cooling. What it does:

• Senses cabinet temperature and switches the compressor or evaporator fan on and off to regulate cooling.
• Helps maintain the user-set temperature range for food safety and efficiency.
• Commonly linked to symptoms such as the refrigerator running constantly, not cooling, or cycling frequently.
• Stop proper cooling when internal contacts wear or the sensor fails.

• Always unplug the appliance before servicing to avoid electrical shock.
• Handle the sensor/capillary carefully; avoid kinks or damage when routing.
• Match and secure all wiring connections and mounting points exactly as removed.

This thermostat is a temperature-sensitive switch that controls power to cooling components as temperatures change. Replacing a worn thermostat restores consistent cycling and more accurate temperature regulation, helping the appliance maintain stable performance. What it does:

• Senses temperature and opens/closes electrical contacts at set points
• Regulates operation of key cooling components to maintain target temperature
• Helps prevent overcooling, overheating, and erratic cycling
• Failure signs include: no cooling, overcooling, temperature swings, unit runs continuously, or short-cycling

• 1 thermostat

• Disconnect power before servicing; verify no voltage is present
• Access the thermostat location; label/photograph wire positions and transfer one at a time
• Install in the same position and orientation as the original to ensure proper thermal response
• Restore power and confirm proper cycling and temperature control

This mechanical thermostat is the appliance's temperature control. It senses internal temperature and opens or closes its electrical contacts to cycle the system, helping the unit reach and maintain the setting you select for consistent performance.

• Regulates temperature by switching power to the cooling or heating circuit as needed
• Helps prevent overcooling/overheating and unstable temperatures
• Common symptoms: runs constantly or won't start, temperature too warm or too cold, short-cycling, no response to knob/setting changes
• Visual damage, burnt terminals, or a thermostat that fails continuity tests indicate replacement

• Disconnect power before servicing
• Document wire locations; transfer wires one at a time and secure all connections
• If your unit uses a sensing bulb/capillary, route and secure it exactly as original; do not kink or sharply bend it
• Verify correct mounting and smooth knob/shaft movement, then restore power and test

This electronic freezer control assembly manages the freezer's control functions and settings to help restore reliable temperature regulation and responsive controls when the original control fails. Designed as a direct replacement control module. What it does:

• Controls freezer functions and user settings by communicating with sensors and other system modules.
• Commonly replaces a failed control board when the freezer won't maintain temperature, cycles erratically, or displays control-related errors.
• Restores responsive control panel behavior when buttons or digital settings stop working.
• Used when diagnostics point to control/board faults rather than mechanical components.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Handle the control board carefully and avoid static discharge; use antistatic precautions if available.
• Match connector locations and wire harness orientation; ensure all plugs seat fully before restoring power.
• If symptoms persist after replacement, recheck wiring, sensors, and diagnostic codes before ordering additional parts.

Cold control that regulates cooling cycles to maintain set temperatures in the fresh-food section. Replacing a failed control restores more consistent temperature control and helps prevent food spoilage. What it does:

• Controls compressor/cooling cycles based on the selected temperature setting to maintain cabinet temperature.
• Common symptoms: refrigerator running constantly, not cooling, or temperature cycling irregularly.
• Interfaces with the fridge control housing and wiring to open/close the cooling circuit as needed.

• Disconnect power to the appliance before starting any repair.
• Access the control housing/panel to remove the old control; note wire locations or take a photo for correct reinstallation.
• Handle any attached sensor or capillary tube gently to avoid kinks or damage.
• After installation, restore power and the refrigerator reaches and holds the desired temperature.

A direct-replacement temperature control that restores user control over oven/refrigerator temperature settings for reliable cooking and storage. Replaces a worn or failed control to help stabilize temperature cycles and improve performance. What it does:

• Regulates appliance temperature by opening and closing the control circuit as needed
• Helps correct symptoms like inconsistent temperatures, unit running too long, or failure to reach set temperature
• Works as the control interface between user settings and the heating/cooling system
• Designed to match OEM function and mounting for straightforward replacement

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Use basic hand tools; mounting screws and wiring retainers are typically reused unless new hardware is supplied
• Note wiring locations and take a photo before disconnecting connectors to ensure correct reassembly

This temperature control thermostat regulates your refrigerator's cooling by sensing cabinet temperature and cycling the compressor. Replacing a failed control restores consistent temperatures and normal on/off operation.

• Monitors cabinet temperature via a capillary sensing bulb
• Opens/closes electrical contacts to start and stop the cooling system
• Common symptoms of failure: too warm or too cold, runs constantly or won't run, no response to temperature dial, intermittent cooling
• Restores predictable cycling and temperature regulation

• Disconnect power before servicing
• Photograph/label wire positions; transfer any brackets/insulators from the original control
• Route the capillary tube exactly as original; avoid kinks and ensure the sensing bulb is secured in its clip/well
• After installation, set to a mid setting and allow up to 24 hours for temperatures to stabilize

This temperature control assembly monitors and helps regulate appliance temperature so the unit maintains expected cooking/cooling performance and resolves temperature-related operation issues. It replaces a failed control to restore consistent temperature response. What it does:

• Senses and controls internal temperature to help maintain set points
• Can correct symptoms such as incorrect temperature, extended heat/cool cycles, or inconsistent performance
• Interfaces with the appliance control system to activate heating/cooling components as designed
• Mounts in the control area and connects to existing wiring harnesses for direct replacement

• Disconnect power to the appliance before starting any service
• Access may require removing the console or rear access panel; follow the service manual for your model
• Handle the control assembly and connectors carefully to avoid damage; match wire locations during reassembly

Replacement cold control that restores temperature regulation in compatible refrigerators. Installs behind the temperature knob to control compressor cycling, helping stabilize interior temperature and stop constant running or temperature swings. What it does:

• Regulates refrigerator temperature by switching compressor/fan operation on and off.
• Replaces a failed temperature control that causes inconsistent cooling or interior temps that are too warm or too cold.
• Can stop issues like the compressor running continuously or frequent temperature fluctuations.
• Works with compatible refrigerator control housings and knobs.

• Disconnect power before replacing the control to avoid shock or injury.
• Note wire locations and knob orientation before removing; reconnect wires to the same terminals.
• Handle the control carefully and avoid bending or stressing mounting tabs and contacts.
• After installation, restore power and verify proper cycling and temperature stabilization.

This temperature control thermostat regulates the refrigerator compartment temperature by cycling the cooling system on and off. Replacing a faulty control restores consistent cooling and normal on/off operation so food stays at the right temperature.

• Senses compartment temperature and opens/closes electrical contacts to start or stop cooling
• Useful when the fridge is too warm or too cold despite adjustments
• Common symptoms: runs constantly or won't run, temperatures don't respond to the dial, no click or change when turning the control
• Also called a "cold control"; restores functional temperature adjustment

• Disconnect power before servicing
• Note wire locations and transfer them to the new control
• Carefully route the sensing capillary in the original path; avoid kinking or sharp bends
• Set to a mid-range setting and allow up to 24 hours for temperatures to stabilize

This thermostat is the temperature control switch that helps regulate cooling by turning the compressor or evaporator system on and off as needed, restoring proper temperature performance and reducing run time when working correctly. What it does:

• Senses temperature and opens/closes the circuit to start or stop the cooling system
• Helps maintain set temperatures by cycling the compressor or evaporator fan
• Commonly replaces a unit that causes inconsistent temperatures, constant running, or short-cycling
• Works as the primary control for the appliance's automatic temperature regulation

• Always unplug or disconnect power before accessing or servicing electrical components
• Handle any attached capillary tube gently; avoid kinks or sharp bends
• Verify correct mounting and wire connections match the original before restoring power

This temperature-sensing thermostat monitors and regulates appliance temperature to restore proper cycling and consistent performance. Replacing a failed thermostat helps resolve temperature drift and heating or cooling irregularities. What it does:

• Senses internal temperature and opens/closes the electrical circuit to control heating or cooling components.
• Restores correct on/off cycling so the appliance reaches and maintains the intended temperature.
• Common symptoms it can address: unit won't reach target temperature, runs too long or too short, or temperature fluctuates.
• Works as a safety and control device to prevent thermal extremes when functioning properly.

• Disconnect power to the appliance before beginning any repair to avoid shock or injury.
• Access may require removing exterior or interior panels; keep track of screws and fasteners.
• Match wiring terminals and orientation to the original thermostat; do not force connectors.