Washer Dryer Combo Burner & Related Parts

The Dryer Gas Valve Coil Kit is an OEM replacement part for Whirlpool dryers, as well as Kenmore and Samsung dryers. It is a set of coils that control the flow of gas fuel to the burner. The gas valve regulates the precise amount of gas needed to properly combust and generate heat for drying clothes. 

Causes of a bad gas valve coil can be wear and tear from regular use, lime or mineral buildup on the coils over time, or physical damage to the coils.

Symptoms of a bad gas valve coil kit include:

• Inconsistent or incomplete drying  
• Slow or intermittent drying
• Burning smell from the gas dryer
• Improper burner ignition or non-ignition

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Dryer Gas Valve Coil Kit is an OEM part for Frigidaire dryers. This kit includes solenoid coils necessary for the opening and closing of the gas valve during the drying cycle. These coils are vital for controlling the flow of gas into the burner, enabling the ignition and maintaining the flame required to dry clothes effectively. 

Symptoms of a bad Dryer Gas Valve Coil Kit include:

• No heat or insufficient heat in the dryer.
• The dryer stops heating partway through the cycle.
• A "clicking" noise when the dryer attempts to ignite the gas flame but fails.
• Gas smell from the dryer, indicating incomplete combustion.

Causes of a bad coil kit can include electrical failure within the coils, mechanical wear from repeated use, or overheating that damages the coil's integrity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This genuine OEM replacement part is a gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential functions. If the dryer is no longer drying clothes effectively, or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is an easy fix.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old valve assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

This burner assembly restores proper gas flame and heat in your dryer. It directs and mixes gas and air for clean ignition at the igniter, helping clothes dry efficiently and consistently.

• Provides the flame path and mixing chamber for gas ignition
• Helps resolve symptoms like no heat, intermittent heat, or very long dry times
• Can address issues where the burner won't ignite or the flame will not stay lit
• Designed to fit the factory burner mount and align with the igniter and flame sensor

• Disconnect power and shut off gas supply before servicing; allow the appliance to cool
• Access is typically from the front lower panel or burner compartment
• Transfer any reusable hardware from the original assembly if required
• After reassembly, restore gas and check all connections for leaks using a soapy water solution

This valve assembly controls incoming water flow to the appliance, restoring correct fill and preventing overfill or no-fill conditions when the original valve fails. It's a direct-replacement style part for affected units. What it does:

• Opens and closes to admit water during fill cycles so the appliance gets the correct amount of water
• Prevents continuous flow when closed, stopping overfills and leaks
• Helps resolve symptoms like no water fill, slow or weak filling, continuous water flow, or related fill/flood error codes
• Works with existing supply lines and mounting points when the original valve is removed

• Disconnect power and shut off the water supply before beginning service
• Drain remaining water from the appliance and have towels ready to catch drips
• Replace the old valve, reattach supply hoses and electrical connectors securely, and tighten fittings to OEM torque recommendations
• After installation, restore power and water, run a test cycle, and inspect all connections for leaks

This surface burner head directs gas to create a controlled flame for stovetop cooking. It replaces a worn or damaged burner to restore even heating and reliable ignition on gas ranges. What it does:

• Distributes gas and shapes the flame for efficient cooking
• Helps maintain even heat under cookware for consistent results
• Can resolve issues like weak or uneven flames and poor burner performance
• Works with the burner cap and base to ensure proper ignition

• One replacement surface burner head

• Turn off the range and gas supply and allow all parts to cool before servicing
• Lift off the cooktop grate and burner cap to access the burner head; no special tools typically required
• Clean mating surfaces and ensure the burner head seats flat before testing