Washer Dryer Combo Screws, Nuts, Washers

This is a #8-18 by 5/8-inch Torq II-head screw used to secure appliance panels and components. It provides a reliable fastener option when replacing stripped or missing screws to restore proper fit and reduce vibration or rattling. What it does:

• Secures trim, panels, brackets or small components to appliance frames
• Restores proper alignment and reduces noise from loose parts
• Replaces worn, stripped, or missing fasteners to prevent further damage
• Compatible where an 8-18 thread and 5/8" length with a Torq II-style head are specified

• One screw

• Use the correct Torq II driver bit to avoid cam-out or head damage
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• If replacing rusted or stripped screws, inspect mating threads and replace as needed
• Disconnect power and follow appliance safety instructions before servicing

A replacement 10-24 x 3/8 machine screw used to secure panels, brackets, and components in compatible household appliances. Provides a straightforward hardware replacement to restore proper fastening and alignment. What it does:

• Fastens panels, brackets or assemblies where a 10-24 threaded machine screw is required
• Restores secure connections that can reduce vibration and rattling
• Replaces stripped or missing screws that prevent proper component alignment
• Compatible with metal-to-metal or metal-to-plastic mounting points that use a 10-24 thread

• Disconnect power to the appliance before working on internal components
• Use the correct screwdriver or nut driver to avoid stripping the head
• Thread the screw in straight and hand-start to avoid cross-threading; tighten snugly but do not overtighten
• Replace any damaged mating hardware or inserts for a secure repair

This SCR 8-18 AB 1/2 is a replacement silicon controlled rectifier that restores proper power control to the appliance's control circuitry, helping the unit switch and regulate current reliably. What it does:

• Controls current flow in the appliance's power/control circuit for timed or regulated output
• Replaces a failed or intermittent SCR to stop erratic cycling, no-power, or control malfunctions
• Commonly used where electronic switching or phase control is required
• Helps restore stable operation when heating or motor circuits fail to receive proper control signals

• One SCR 8-18 AB 1/2 replacement component

• Disconnect power to the appliance before inspecting or replacing electrical components
• Observe ESD precautions and handle the SCR by its body; avoid touching leads
• Verify wiring and mounting orientation match the original part before final assembly

The agitator screw secures the washer's agitator to the drive shaft so it can move clothes effectively during the wash cycle. Replace a lost, stripped, or rusted screw to help stop wobble and restore proper agitation.

• Fastens the agitator to the drive shaft/coupler to transfer motion
• Address a loose or wobbly agitator, rattling/clunking, or weak/intermittent agitation
• Replace if the original screw is missing, corroded, or has stripped threads or head
• Helps prevent the agitator from lifting off during operation

• Disconnect power and ensure the washer is empty before servicing
• Remove the fabric softener dispenser and agitator cap to access the fastener
• Align parts, start the screw by hand to avoid cross-threading, then tighten snugly—do not overtighten
• Reinstall caps/dispenser and run a brief test cycle to proper agitation

A replacement mounting screw to secure appliance panels and components so parts stay properly fastened during normal use. Small but essential hardware for stable, rattle-free operation and reliable repairs. What it does:

• Fastens panels, brackets or components to the appliance chassis
• Prevents loose panels, vibration noise, or parts shifting during operation
• Used when original screw is lost, damaged, or stripped
• Restores proper fit and alignment after disassembly for service

• Disconnect power and water before starting any repair
• Use the correct screw type and length; do not force or substitute oversized fasteners
• Tighten until snug—avoid overtightening to prevent stripped threads or cracked parts
• Keep small parts away from children and pets

A small hex nut used to secure components and fasteners on compatible Whirlpool appliances. Replaces a worn or missing nut to restore proper part retention and reduce noise or loose fittings. What it does:

• Secures panels, brackets, or components that use a matching bolt or stud
• Helps prevent rattling, vibration, or parts coming loose during operation
• Restores a proper threaded connection when the original nut is stripped or missing
• Works wherever the correct thread size and profile are required

• Unplug the appliance or disconnect power before starting any repair
• Use the correct-size wrench or socket to avoid rounding the nut
• Tighten securely but avoid overtightening, which can strip threads or crack parts
• Inspect mating bolts/studs and replace if damaged