Washer Hose Or Tube

Pressure tube connects washer tub to water level switch. Replace if cracked, kinked, or clogged to restore proper water level sensing in your laundry center.

Carries water from home supply to washer inlet valve. Replace if your hose is cracked, worn, leaking, or damaged by pests or age. Restores proper fill.

Flexible hose for washers that connects water or drain lines between components. Replace if your hose is cracked, collapsed, clogged, or leaking.

5 foot. Package of 2.

This hose kit replaces worn or damaged appliance hoses to restore proper water flow and prevent leaks. It's a direct-fit replacement for compatible Whirlpool systems and helps stop visible leaks and restore normal fill/drain operation. What it does

• Replaces cracked, split or leaking hoses to stop water loss and reduce risk of appliance damage
• Restores reliable water flow for filling and draining functions
• Helps eliminate poor draining, intermittent filling, or water pooling near the appliance
• Works with existing clamps and connections when installed correctly

• Disconnect power and shut off the water supply before starting any repair
• Inspect connection fittings and replace clamps if worn; ensure a snug, leak-free fit
• Route hoses without kinks and secure to avoid chafing or strain
• After installation, run a short cycle and check all connections for leaks

Drain pump hose assembly for washers. Connects the drain pump to the outlet. Replace if cracked, leaking, or connector is damaged or missing.

Washer air chamber connects the water level pressure switch to the tub. Replace if cracked, kinked, or disconnected causing water level issues.

Joins your washer's water line to internal plumbing with a secure, leak-resistant connection. Replace this connector if cracked, worn, or leaking.

Kit contains two 10 feet inlet hoses.

This is a rubber or plastic hose that connects the water inlet valve to the detergent or fabric softener dispenser in the washing machine. It carries water into the dispenser housing to flush soap or additives into the wash drum at the correct time during the cycle. Replace this hose if you see leaking near the dispenser area, the dispenser is not filling with water, or the hose shows cracks and deterioration.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

Connects your washer to the household water supply. Replace if hose is cracked, leaking, worn, or damaged to prevent water damage and ensure proper fill.

Replacement drain hose that routes wastewater from your washer to the household drain. Needed when the original hose is damaged, cracked, or clogged.

These replacement 6" FXF vacuum bags capture dust and debris to restore pickup performance and keep the appliance's airflow and motor compartment cleaner. Designed as a direct-fit consumable for compatible bagged upright and canister vacuums. What it does:

• Collects dirt, dust and debris so particles stay contained for easier disposal
• Helps maintain suction by keeping the vacuum's intake and motor chamber clearer
• Reduces dust and allergen re-distribution compared with a torn or overloaded bag
• Replaces worn or full bags that cause reduced capacity, visible dust escaping, or increased odor

• Always unplug the vacuum before removing or installing bags
• Remove the full bag carefully to avoid spilling debris; seal and dispose per local regulations
• Verify correct orientation and secure fit before operating to avoid leaks
• Replace bags regularly; inspect the inlet collar and seals for wear when servicing

This 6-foot rubber hose provides a flexible, durable connection for appliance water/drain routing, helping restore proper flow and reduce leaks. Designed as a direct replacement hose where a 6' rubber line is required. What it does:

• Replaces worn, cracked or brittle 6' rubber hose to stop or prevent leaks.
• Restores flexible routing for water supply or drain lines that need a 6-foot rubber connection.
• Helps eliminate kinks and restricted flow caused by damaged hoses.
• Compatible with standard hose clamps or quick-connect fittings used on many appliances.

• Turn off water and power to the appliance before starting any work.
• Inspect fittings and clamps; replace clamps if corroded or damaged for a secure seal.
• Push hose fully onto the fitting and secure with the proper clamp type; test for leaks before returning appliance to service.

This U-shaped mounting bracket secures and guides the drain hose at the back of the washing machine, keeping it properly positioned during the drain cycle. It prevents the hose from slipping out of the standpipe or laundry tub. Replace this bracket if the drain hose keeps falling out of position, water is spilling during the drain cycle, or the original bracket is cracked or broken.