Need Help?
Call
Channels household water to your washer's fill system. Replace if cracked, leaking, or worn to restore proper flow and prevent water damage to floors.
Replaced Read more
This is the flexible drain hose that carries used water from the washer's pump to the household drain. Replacing a cracked or kinked hose helps prevent leaks and restores proper draining performance.
Unplug from electric socket. Pulled the washer away from the wall. Have a container ready to catch any water remaining in the hose. Remove the hose from the drain in the wall and drain into container. Unsnapped the hose from the guide on the back side of the washer and removed the plastic piece around the hose on the outside of the case where the hose enters the inside of the case. Took off the front of the case, removing two screws from the bottom of the front and two from the underside of... Read more
Carries wastewater from the washer tub to your household drain. Replace if cracked, kinked, split, or leaking to restore proper drainage function.
Removed the back of the washing machine, removed the hose and installed the new one easy peasy... Read more
Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.
I ordered the drain extension kit and the hose connector kit. Read more
Two 5-foot nylon braided hoses connect household water supply to washer inlet valves. Replace cracked, leaking, or aging hoses to prevent water damage.
Watched u tube video. Ordered replacement water inlet valve and new hoses. Dismantled washer and replaced defective valve and installed new hoses. The repair went very easily and the washer worked perfectly as a result. Read more
Contains two, six foot long braided hoses with 90 degree ends.
I had a problem with the drain pump on my Kenmore HE3 and I replaced it using a drain pump I ordered from APP. That fixed that problem but once I started running the washer I started getting a FH error code. I looked it up and found that it was a problem with the washer not filling properly. I pulled the washer out and found that one of the fill hoses had kinked when I pushed the washer back in place. There was also some writing on the hose that read "Change hose every five years". I know I had... Read more
Connects washer drain hose to extension hose. Includes coupling and clamps. Replace if cracked, broken, or when extending drain hose length to reach pipe.
Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138
Just took off the old vacuum break and put the new one on. It was very easy because the site had a video showing how and I watched it first. Read more
Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.
Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more
This is a flexible hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. If you notice detergent not dispensing properly, leaking near the dispenser area, or water pooling under the washer during the fill cycle, this hose may be cracked, clogged, or disconnected and needs replacement.
21-inch drain hose extension for washers. Extends existing drain hose when original is too short to reach standpipe. Includes clamp for secure fit.
Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly. Now we're washing again and no leaks! Read more
This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.
This is a flexible drain hose that connects the washing machine's pump to the household drain standpipe or laundry tub. It channels used wash and rinse water out of the machine during the drain and spin cycles. Replace this hose if you notice leaks at the connections, cracks or splits in the hose material, or if the washer is not draining properly due to a restricted or damaged hose.
This is a small hose that connects to the dispenser valve assembly inside the washing machine, directing water into the detergent or fabric softener dispenser. It ensures proper water flow to the dispenser during the wash cycle. Replace this hose if you notice leaking near the dispenser area, detergent not being flushed into the drum, or visible cracks and deterioration on the hose.
Changed upper plate & inlet hose real easy. Read more
Replacement flexible hose that routes water inside your washer. Needed when original is cracked, kinked, worn, or leaking. Restores secure flow.
Purchased the WPL 40922 hose kit. This kit is reasonably priced and has everything you might need to retrofit to most legacy Whirlpool brand washers. The fix went well and I also cleared the water solids build-up on the fill nozzle at the inlet to the wash tub. Read more
Connect hot and cold water faucets to your washer's inlet valves with this 2-pack of 5-foot fill hoses. Replace aging, cracked, or leaking supply lines.
Purchased water inlet valve and new hot and cold water hoses. Unscrewed about 5 screws that were holding the top of the washer in place then slide the top forward and up. Released the control top it popped off no screws. Disconnected the wires attached and unscrewed 2 screws holding the valve in place the popped that off. Popped in a new valve and repeated the process in reverse. Boom done! Very simple works like new! Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.