Washer Leg Or Foot

Adjustable leveling foot that supports and stabilizes your refrigerator. Replace if worn, broken, or missing to eliminate wobbling and vibration.

Adjustable leveling foot that installs on the bottom of your washer to provide stable support. Replace when cracked, worn, or missing to restore balance.

Adjustable support legs located at the bottom corners of your washing machine that ensure proper leveling and stability. Replace when legs are bent, stripped, or cannot maintain proper height adjustment, causing excessive vibration or rocking.

Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.

Leveling leg assembly for washers. Installs at the corners to stabilize and level your machine. Replace if cracked, broken, or missing threads.

Threads into the washer base to adjust height and stabilize the unit. Replace if cracked, stripped, or missing to eliminate rocking on uneven floors.

Adjustable leveler leg that stabilizes and levels compatible Whirlpool appliances. Replacing a worn or damaged leveler restores proper balance, reduces rocking, and helps doors and drawers align and seal correctly. What it does

• Raises or lowers the appliance to achieve a level position on uneven floors.
• Stops rocking or wobbling that can cause noise or uneven wear.
• Helps doors and drawers close and seal properly by correcting tilt.
• Replace when threads are stripped, the foot is broken, or the leg no longer holds height.

• Disconnect power (and water supply for appliances with hookups) before working beneath or behind the unit.
• Support the appliance securely (use blocks or have a helper) before removing or adjusting levelers.
• Most levelers screw in/out—turn to raise or lower, then test stability and door alignment.

Adjustable leveling leg for washers. Securely holds machine in place while allowing height adjustment on uneven floors. Replace if stripped or seized.

Adjustable leveling leg with foot pad for dryers, washers, and pedestals. Replace cracked, broken, or missing legs to stabilize your appliance.

Adjustable leveling leg stabilizes your dryer on uneven floors. Replace if cracked, broken, or worn from vibration and repeated adjustments.

This leveling leg assembly supports and stabilizes your washer by allowing you to adjust its height for a level installation. Keeping the appliance level helps reduce vibration, noise, and movement during operation.

• Adjusts the washer's stance to ensure it sits level on the floor
• Helps prevent excessive vibration, walking, and rattling noises
• Supports proper spin performance by improving machine stability
• Common fix when a foot is worn, damaged, or will not hold adjustment

• Unplug the washer and turn off water supply before servicing
• Tip the appliance carefully to access the leveling point
• Thread the new leg into the base and adjust until level; lock if applicable
• Verify all legs contact the floor firmly and recheck level after test run

Adjustable leveling leg threads into washer base to stabilize and level the cabinet. Replace worn, missing, or broken legs to prevent rocking and vibration.

The leveling leg assembly is an adjustable support system located at each corner underneath your dryer to ensure proper alignment and prevent vibration during operation. These threaded legs allow you to level the appliance and create stable contact with the floor surface. Replace if legs are damaged, won't adjust, or cause excessive vibration or movement during the spin cycle.

Leveling leg for washers. Installs at the base to support and level your machine. Replace if cracked, broken, worn, or missing for proper stability.

This rubber foot pad sits at the bottom of your washer's leveling leg to provide stable, non-slip contact with the floor. It prevents the washer from sliding during operation and protects your floor from scratches or damage. Replace this pad if your washer moves during spin cycles, makes noise against the floor, or the rubber foot is cracked or missing.

This replacement rubber foot cushions the machine's contact point with the floor to improve stability, reduce vibration, and protect surfaces. Replace a worn or missing foot to restore steadier, quieter operation and easier leveling.

• Provides a cushioned, non-slip contact point between the appliance and floor
• Helps absorb vibration and reduce rattling or movement during cycles
• Aids in proper leveling and overall stability
• Replace when cracked, flattened, or missing, or if the unit rocks or "walks"

• Disconnect power; for washers, also turn off water. If applicable, shut off gas supply
• Carefully tilt or raise the appliance with assistance and proper lifting support
• Remove the worn foot and install the new foot on the leveling leg or base as designed, ensuring it seats fully
• Re-level the appliance and tighten any locknuts; verify stable operation