Bumper, Bushing, Grommet Parts

This spacer fits between mating parts in select GE cooking appliances to set correct clearance and alignment. Replacing a worn or missing spacer helps secure the assembly and prevents rubbing or damage to adjacent surfaces during use.

• Maintains proper spacing so hardware tightens squarely and components sit evenly
• Helps prevent metal-to-metal contact that can cause noise, wear, or surface damage
• If missing, broken, or deformed, you may notice looseness, misalignment, rattling, or scraping
• Restores original fit and finish when replaced

• Disconnect power; if applicable, shut off gas. Allow the appliance to cool completely
• Support the part being unfastened (such as a door, handle, or trim) to avoid strain on panels or glass
• Install the spacer in the same location/orientation as the original and reuse existing hardware if serviceable
• Tighten screws evenly; do not overtighten against glass or enameled surfaces

Specs: .875`` long

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

This factory shim is a thin spacer used to set precise clearance between mating parts in your appliance. It restores correct alignment to stop rubbing or looseness, helping doors and assemblies operate smoothly and seal as designed. What it does:

• Provides precise spacing for proper fit and alignment of components
• Helps address rubbing, binding, squeaks, or uneven gaps from minor misalignment
• Supports proper closure and sealing when used in hinge or bracket areas
• Replaces a worn, missing, or damaged shim that can cause looseness or vibration

• 1 shim

• Disconnect power before servicing; if working near water connections, shut off the water supply
• Support the door or component before loosening fasteners to avoid strain on hinges/brackets
• Install the shim in the same location and orientation as the original for correct spacing
• After reassembly, retighten hardware as needed

This is an authentic OEM freezer basket bumper sourced directly from the manufacturer for use on freezer baskets. Freezer basket bumpers are attached to the baskets to keep them from sliding around inside the freezer. If the bumper breaks, the basket will not stay in place, and the contents could shift or fall out. Freezer baskets create more storage room inside a freezer. These baskets are normally located on the bottom of the freezer, with freezer racks located above. Freezer baskets are ideal for storing smaller packages that might not stack well on the racks. Over time, normal wear and tear may cause the bumper to crack or break completely; if this happens, the bumper should be replaced. Remove the contents of the freezer basket. Remove the freezer basket from the freezer. Push the new bumper onto the freezer basket. Replace the contents of the basket and put it back into the freezer. This handle freezer basket is made of high-quality, white molded plastic. It is designed for use in freezers manufactured by Frigidaire, Kenmore, Gibson, and Electrolux.

The Spacer is an OEM part for Whirlpool microwaves. It is used to create a specific distance between components, ensuring proper alignment and function within the microwave. This spacer is critical for maintaining the correct positioning of parts during operation.

You should replace this spacer if it becomes damaged or worn out. Causes of a bad spacer can include mechanical stress, heat exposure, or accidental damage during repairs or maintenance. A compromised spacer can lead to misalignment of microwave components, affecting overall performance.

Symptoms of a bad spacer include:

• Misalignment of internal parts
• Unusual noises during microwave operation
• Improper functioning of the microwave components

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This spacer maintains the correct distance between mating components in your appliance's assembly so parts align and operate smoothly. Replacing a worn or missing spacer can correct looseness, rubbing, or vibration-related noise.

• Holds a precise gap between parts for proper alignment and motion
• Prevents metal-to-metal contact and premature wear
• Helps reduce vibration, rattling, and scraping noises
• Common signs include misalignment, unusual gaps, looseness, or rubbing in the related assembly

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Refer to your model's diagram to locate the spacer's exact location and orientation
• Inspect related fasteners and bushings; replace if worn
• Do not overtighten hardware to avoid deforming the spacer

Replacement bumper that cushions appliance parts and absorbs shock to prevent rubbing, rattling and surface damage. Restores proper fit and quieter operation for components that contact cabinets, doors or panels. What it does:

• Cushions contact points to reduce noise from doors, drawers or panels.
• Prevents metal-to-metal or metal-to-surface scraping that can cause wear or cosmetic damage.
• Helps components close and seat more evenly to reduce vibration and movement.
• Common symptom fixes: eliminates rattling, stops rubbing noises, and prevents chipping or scuffing where parts meet.

• One bumper.

• High-level, tool-light replacement; usually presses into or adheres to the mounting surface.
• Disconnect power or unplug the appliance before opening panels where required.
• Inspect surrounding clips/retainers and clean the mounting area for best adhesion or fit.

This stand off is a small mounting spacer that secures and spaces internal components, restoring proper alignment and reducing panel movement or vibration for quieter, more reliable operation. What it does:

• Provides a solid mounting point to hold panels, brackets or wiring harnesses in place.
• Replaces broken, cracked or missing standoffs that allow components to shift or rub.
• Helps stop rattling, buzzing or misalignment caused by loose mounting points.
• Keeps proper clearance between parts to prevent wear or chafing over time.

• Disconnect power to the appliance before starting any repair.
• Remove the affected panel or access cover to reach the damaged standoff.
• Replace the old standoff with the new part; retain and reuse any existing screws or fasteners unless damaged.
• Hand-tighten mounting hardware and test the appliance; avoid overtightening plastic standoffs.

The Motor Bushing is an OEM part for Frigidaire refrigerators. The bushing works to reduce vibration and surrounds the motor shaft, facilitating smooth rotational movement.

Causes can be normal wear over extensive use, lack of lubrication that increases friction, or damage from foreign object intrusion.

Symptoms of a bad motor bushing include:

• Excessive vibration causing noise during motor operation
• Reduced fan blade spinning speed or complete stoppage
• Motor shaft wobble or misalignment over time

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

Small rubber bumper that cushions appliance components to reduce noise, prevent metal-on-metal contact, and protect finishes; replaces worn or missing bumpers to restore quiet operation and prevent damage. What it does:

• Absorbs shock and vibration to stop rattling or buzzing
• Prevents doors, drawers or panels from banging or scraping
• Protects painted and metal surfaces from wear and chipping
• Helps restore proper spacing and alignment of moving parts

• Always disconnect power to the appliance before servicing
• Typically installs by pressing into a mating hole or seating on a flat surface; some applications use adhesive
• Inspect mating surface for damage or debris and replace any additional worn bumpers for even contact

The Refrigerator Fan Motor Grommet is an essential component for maintaining the efficiency of your Samsung refrigerator. This genuine OEM part ensures a perfect fit and seamless integration with your appliance, enhancing overall performance. Designed to securely hold the fan motor in place, it minimizes vibrations and reduces noise, providing a quieter kitchen environment. The durable construction of the grommet ensures long-lasting functionality, protecting the motor from dust and debris. Installing this part helps maintain optimal airflow within the refrigerator, ensuring consistent cooling and preserving the freshness of your food. Compatible with a wide range of Samsung refrigerator models, the Refrigerator Fan Motor Grommet is easy to install, making it a convenient solution for DIY repairs. By choosing this genuine OEM part, you can trust in the quality and reliability that Samsung is known for, ensuring your refrigerator operates smoothly and efficiently for years to come.

The Refrigerator Door Hinge Shim is designed to ensure your refrigerator door operates smoothly and stays properly aligned. This genuine OEM part is compatible with a wide range of Samsung refrigerator models, guaranteeing a perfect fit and reliable performance. The hinge shim effectively compensates for any slight misalignments, helping to maintain the doorGÇÖs stability and prevent gaps or drafts that can affect your applianceGÇÖs efficiency. Installing the Refrigerator Door Hinge Shim is straightforward, allowing you to restore your fridgeGÇÖs functionality without the need for professional help. By choosing this genuine OEM part, you benefit from the quality and durability that Samsung is known for, extending the lifespan of your refrigerator. Whether youGÇÖre dealing with a door that doesnGÇÖt close correctly or aiming to enhance the overall performance of your appliance, the Refrigerator Door Hinge Shim provides a practical and effective solution to keep your kitchen running smoothly.

This spacer is a small mounting support used to maintain proper clearance and alignment between refrigerator panels, doors, or components. It helps reduce rubbing, vibration, and noise by restoring correct spacing and fit. What it does:

• Keeps panels, trim, or components spaced correctly to prevent metal-on-metal contact and wear
• Helps align doors and panels for a flush fit and smoother operation
• Reduces vibration and rattling caused by misaligned parts
• Used wherever a fixed clearance or gap is required during reassembly

• Disconnect power to the appliance before beginning any service that requires panel or component removal
• Inspect mating surfaces for damage or debris before installing the spacer; replace any damaged fasteners
• Install in the same orientation and location as the original spacer; do not overtighten mounting hardware

This small rubber bumper cushions the refrigerator/freezer door to reduce noise and prevent metal-on-metal contact. It helps doors close quietly and protects cabinet finish from repeated impacts. What it does:

• Acts as a soft stop between the door and cabinet/frame to absorb impact
• Reduces rattling and slamming for quieter operation
• Prevents wear and chipping where the door contacts the cabinet
• Restores proper door alignment when missing or worn

• One replacement bumper

• Push the bumper into the existing hole or slot on the door/frame until fully seated
• Inspect surrounding area for damage; replace mounting clips or retainers if required
• Wear gloves to protect hands from sharp edges during installation
• No special tools usually required; for detailed instructions