Cooktop Control Board

This surface element control board manages a dual radiant cooktop burner. It regulates power to the inner and outer coils so the element heats correctly, changes size as selected, and responds accurately to temperature settings.

• Controls power to a dual radiant surface element
• Directs inner/outer ring operation based on size selection
• Modulates heat output to match the set level
• Common failure symptoms: dual burner won't heat, only one ring heats, stuck on high, or erratic cycling

• Disconnect power at the breaker before servicing to avoid electrical shock
• Access is typically under the cooktop or rear top panel; refer to your model's service information
• Move wire connectors one at a time to the new board to maintain correct placement
• Handle the board by the edges and observe ESD precautions

This Whirlpool Range Control Board is an OEM part for a variety of Whirlpool range models. It serves as the electronic brain of the range, managing functions such as temperature regulation, timer settings, and various cooking modes. 

The control board in a range can be susceptible to issues like electrical faults, short circuits, or damage from power surges. A malfunctioning control board can lead to erratic temperature controls, display errors, or non-responsive buttons, hindering your ability to cook effectively.

Symptoms of a defective range control board include:

• The oven fails to heat up or maintain the set temperature.
• Digital displays show error codes or become unresponsive.
• The oven controls do not respond or work intermittently.
• Unusual behavior in cooking modes, such as the broiler activating unexpectedly.
• The oven timer functions incorrectly or not at all.

This genuine Whirlpool OEM replacement part is compatible with Maytag, Jenn-Air, and Kenmore models.
 

This part is a replacement control kit. It is made to replace a broken or ineffective part in some models of ovens and ranges.In order to monitor the temperature and control the oven settings, the control kit needs to be in proper working order. In cases where this part is warped, corroded, worn, broken, or in any way ineffective, the control kit will need to be immediately replaced. Prior to undergoing repairs, it's critical that the oven is entirely disconnected from the power source. Always wear work gloves when attempting an appliance repair.This is a genuine OEM part that has been manufactured by Frigidaire and has been sourced directly from the manufacturer to ensure high quality. This control kit can be used with various different models of ovens and ranges that have been manufactured by brands that include Frigidaire, Electrolux, Gibson, Westinghouse, and others. This is a genuine OEM part and thus is made of high-quality, durable materials and is sold individually.

This part is a replacement touch control board.If the current touch control board is malfunctioning in any way, this part can be used for replacement. It is intended for use with cooktops. This part is required for proper cooktop functionality, as it allows the user to properly control the heating of the surface element. Without this part in proper working order, the cooktop will not function as intended, if at all. It's critical that the appliance is entirely disconnected from the power source before any attempt is made to repair this part. Work gloves should always be worn to protect the hands. This is a genuine OEM part made by GE and has been sourced directly from the manufacturer. This touch control board is suitable for use on a variety of different models of ranges manufactured by a range of brands including General Electric, Hotpoint, and RCA. This is a genuine OEM part and thus is made of high-quality, durable materials.

This electronic clock control helps manage and monitor the features on an oven. This part is located on the front of the oven so the user can easily see the clock and start and stop times for cooking. The display can also show error codes if one of the oven parts is not working correctly. If this part is damaged, cooking may take longer, overheating may occur, or the foods may come out unevenly cooked.Replacing the part is simple and requires only a Phillips screwdriver. Disconnect the oven from power or turn off the appropriate breaker box. Open the door and access the bottom of the control panel assembly. Remove the screws and lift up on the electronic clock control to unhook it from the appliance. Unplug the wire harnesses before removing the clock. Attach the new part to the wires and screw it into the oven.This electronic clock control is made for use as a genuine OEM replacement part for Jenn Air ovens. It is sold on an individual basis and comes directly sourced from the manufacturer. This part is offered as an individual component.

The Encoder Board is an OEM part for LG ovens. This board is responsible for interpreting the inputs from the control knobs and buttons on the oven's control panel. It sends these signals to the main control board, which then adjusts the oven settings accordingly, such as temperature and cooking mode.

Causes of a bad encoder board can include electrical surges, wear and tear from frequent use, or physical damage to the board's components. A malfunctioning encoder board can disrupt the communication between the user interface and the oven's control system.

Symptoms of a bad encoder board include:

• Unresponsive control knobs or buttons
• Incorrect oven temperature settings
• Oven not starting or turning off unexpectedly
• Error codes displayed on the control panel

This OEM LG part is also compatible with Sears/Kenmore.

The Controller is an OEM part for Frigidaire ranges. This part manages the oven's electronic functions, including temperature regulation, cooking modes, and timer settings, ensuring precise and reliable cooking performance.

Common causes of a bad controller include electrical surges, wear and tear of electronic components, or damage due to excessive heat or moisture.

Symptoms of a bad Controller include:

• Inaccurate temperature settings or fluctuations
• The oven not heating up or shutting off unexpectedly
• Error codes or malfunctioning display
• Unresponsive buttons or controls

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Control Board is an OEM component specifically designed for Frigidaire ranges. It is responsible for regulating and monitoring various electrical components of the range such as the temperature display, bake/broil elements, convection fan, and cooktop burners.

Symptoms of a bad control board include: 

• Inaccurate or inconsistent temperature readings
• Unresponsive controls and setting buttons 
• Intermittent or failed cooktop/oven functions
• Error codes appearing on the display

Causes of a bad control board can include exposure to heat over time, damage from liquid spills, or failure of electronic components on the board.

Replacing the control board ensures full functionality is restored. This OEM Frigidaire replacement will integrate seamlessly with all existing wiring and connections on your appliance.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Don't risk further damage - replace yours before issues escalate.
 

The Control Board is an OEM part for Frigidaire ranges. This part controls the oven functions, including temperature regulation, cooking modes, and timer settings.

Causes of a bad control board can include electrical surges, moisture damage, excessive heat, or general wear and tear.

Symptoms of a bad range control board include:

• The oven or burners not turning on
• Unresponsive or malfunctioning control panel
• Incorrect temperature settings
• Error codes displayed on the control panel
• Oven not maintaining set temperature

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a control panel that is used on many ovens. It is an interior part located near the buttons a user can press to turn on the oven, change the temperature, and select cooking methods. The control panel is the component that controls the oven based on which buttons are pressed. It includes a small display screen that shows the temperature, time, or error codes if a part of the appliance is not working correctly.It's important to be sure the range is unplugged before replacing the control panel. A Phillips screwdriver can unthread the screws holding the rear access panel. Pull the panel down and note where the wires are connected to the damaged control panel. Remove the old control panel and position the new one before securing it with screws. Replace the wires on the correct terminals before tightening the screws and replacing the access panel. Turn back on the power and push back the oven before use.This is a genuine OEM replacement control panel used for a variety of Whirlpool ovens. It is sold on an individual basis. A pair of work gloves and basic tools may be required for the replacement process.

This is the electronic oven control board that manages bake and broil temperatures, oven timing, and display functions. Replacing a failed control restores accurate temperature regulation and front-panel responsiveness so your range can cook reliably again.

• Regulates oven temperature by cycling bake/broil elements per setpoint
• Controls oven timing functions and user interface/display
• Common failure signs: unresponsive buttons, error codes, inaccurate temps, no heat, or blank/erratic display
• Designed for direct replacement of the original factory control

• Disconnect power at the breaker before servicing
• Transfer overlay and wiring from the old board to the new one, noting connector positions
• Handle the PCB carefully to avoid static discharge and damage
• After installation, run a test bake cycle

This electronic oven control board manages oven heating functions and the display on gas ranges. Replacing a failed board restores reliable ignition, accurate temperature control, and normal bake/broil operation.

• Regulates oven temperature by reading the sensor and cycling the gas burner through the bake/broil relays
• Drives the clock and function display
• Interprets keypad inputs to select modes and temperatures
• Common failure signs: oven won't heat or maintain temperature, blank or erratic display, unresponsive controls, or recurring fault alerts

• Disconnect power at the breaker and shut off gas before servicing
• Use ESD protection and handle the board by the edges
• Photograph wiring and transfer connectors one at a time; reinstall using existing hardware
• Some models require transferring the original keypad/overlay to the new board

This clock/timer is the range's electronic oven control. It manages the bake and broil circuits using temperature-sensor feedback and provides the digital clock and timer, restoring proper heating performance and a readable display when the original control fails.

• Controls power to bake and broil elements/ignitors to reach and hold the set temperature
• Displays clock, timer, and oven status on the front panel
• Receives keypad inputs to start/stop and adjust oven cycles
• Typical failure signs: blank or dim display, unresponsive controls, error codes, oven will not heat or maintain temperature

• Disconnect power at the breaker before servicing; this control carries live voltage
• Access the control from the backguard/control panel; remove the rear cover to reach mounting screws and connectors
• Photograph or label all wire harness connections; transfer any brackets and install the new board in the same orientation
• Handle electronics by the edges and protect from static discharge; set the clock after reassembly and test oven functions

This electronic oven control board is the brain of your range or wall oven. Replacing a failed board restores the display and keypad response and allows the appliance to heat and run bake/broil cycles reliably again.

• Controls relays for bake and broil circuits
• Uses oven sensor feedback to regulate and maintain temperature
• Powers the time/temperature display and reads keypad inputs
• Common symptoms: blank or erratic display, unresponsive buttons, F-code errors, oven won't heat or shuts off mid-cycle

• Disconnect power at the breaker before servicing; allow the appliance to cool
• Static-sensitive component—handle by the edges and avoid touching circuitry
• Note/photograph wire locations; transfer connectors one at a time to the new board
• Mount the board in the control panel, secure connections, restore power, and test

This factory fixing kit supplies the OEM hardware required to secure the appliance or designated components during installation or service. Replacing missing or damaged fasteners restores a solid, aligned mount so the unit stays stable without shifting, rattling, or gaps.

• Provides the correct hardware to fasten parts per your model's installation or service instructions
• Replaces stripped, corroded, or missing screws/clips that lead to looseness
• Helps maintain alignment and clearances to prevent gaps, rattles, or vibration
• Typical symptoms: loose mounting, panels that shift, or movement when opening/closing doors or drawers

• Disconnect power; shut off water or gas if applicable before starting work
• Follow the model-specific installation/service manual for attachment points and sequence; use the proper driver bit and do not overtighten
• Verify the unit is level and securely anchored; check clearances and operation after securing

This main electronic control board (PCB assembly) manages and coordinates your appliance's functions. Replacing a failed board can restore reliable power distribution and control of motors, valves, and other components, helping resolve no-power and erratic-operation issues.

• Directs power and timing to motors, heaters, fans, valves, and lights based on inputs from sensors and the user interface
• Interprets sensor feedback and can shut down components when faults are detected
• Failure symptoms include no power or no start, unresponsive controls or display, cycles that won't advance, intermittent shutdowns, or error codes
• May present as loads not running when commanded or visible board damage (burn marks or stuck relays)

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the board by the edges and avoid touching components or traces
• Photograph wiring and move connectors one at a time to the matching positions on the new board
• Secure the board and ensure all harnesses are fully seated; perform any model-specific reset/initialization per the service manual