Cooktop Parts

• Noisy
• Tray won't turn

I fix this problem by purchasing a new turntable motor. Simple 5 minute installation. Read more

• Won't start
• No heat

Unplugged range, removed back panel. Loosened plug block from range, unhooked wires from existing element, then sliced through insulation between element ends with sharp knife. Removed screws holding element ends then removed element. Inserted new element, screwed it in place, connected wires and replaced plug block. Vacuumed up fiberglass insulation dust and replaced back panel. Replaced plug then tested. Read more

I'm a 56 year old divorced woman. I started doing these kinds of repairs to save some money and honestly, to see if I could. So yes, if I can do it, it's not that tough to do. My microwave is built in above the stove - getting it down and back up was the hardest part of the job. An extra pair of strong hands really helps-for anybody, not just a 56 year old woman. The actual repair was pretty easy. Most likely problem was pretty obvious after a little research. Easy to take off cover, get... Read more

Removed bottom flame cover in lower oven to find the ignitor was actually broken into pieces. We assume it exploded because the bottom side of the cover had a hole blown in it and had to be hammered flat. Before it totally stopped working we had experienced a number of instances where the GFI kicked out when the oven was preheating. Order the GE specific replacement part from Appliance Parts Pros which arrived promptly. The replacement was fairly simple...being careful not to damage the new... Read more

My 18+ year old Jennair cooktop, PN CCG2520W was in need of a rebuild b/c of a welded venturi tube on the right front [RF] burner. In order to remove the glass top cover, you MUST remove the venturi tube. To do this you have to DRILL-OUT the venturi tube which requires a new venturi and orifice holder. The repair was difficult b/c most of the parts are no longer available. But then I found a ray-of-hope. I was able to find some Jennair (Maytag) parts but they are scarce. Later I found... Read more

Replaced above parts, easy to do, looks like a new stove. Needed to pry open knob stem slot segments very slightly to remove broken plastic from previous knobs. Spreading stem slot metal sides too much and they will break. With slots cleaned out, pinch stem sides almost together for new knobs to slide on. Customer service rep was helpful and parts delivery was next day as promised. Before contacting Appliance Parts Pros, I found their on-line customer reviews were much better than their... Read more

Switches needed to be replaced. Make note of where each screw comes from. They were not all the same. To remove the front panel and get to the switches, you have to partially remove the cook top. Removed 5 screws from the back to release the cooktop. Slid the cooktop back far enough to expose screws holding on the front panel. Removed 4 screws from the top and 6-8 from the bottom (opened the oven door to get to the bottom screws). Removed screws from the front panel holding the switch in... Read more

REPLACED THE ELEMENT. Read more

Replaced the burner. Order arrived in under 2 days as stated, very pleased. Read more

With the help of Ms.Kelly Hunt, AppliancePartsPros.com, I was able to locate the correct parts. It took approx. 30 minutes to remove the door and replace the shattered glass and bottom door trim. I wouldn`t hesitate to use this service for future use.The staff is friendly, helpful , knowledgeable and delivery is very fast. Thank you Martin Dobbins Read more

We ordered a igniter and a new regulator. My husband installed the parts it works great now. Read more

Ordered and replaced it with a new 8" Surface Burner from you. Read more

Replaced the oven burner, ignitor, and the safety valve. Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

After doing some research the problem appeared to be the door safety switches. I ordered 3 new ones to replace all the original ones. Some minor disassembly of the microwave front was required to reach the fuse and switches. To reach the switches the control panel wires needed to be unplugged and the panel removed. After doing that replacing the switches was pretty strait forward. As of this comment the microwave has worked for 5 days without blowing the fuse so far. This has probably fixed the... Read more

I went online to Appliance Parts Pros and with only my model # and serial # of my range, it was a simple fix! They not only had the part I needed, but they provided the expanded drawing so I could see what was needed and when I had a question and emailed them, I received a response within a couple of hours. They shipped right away and the glass was at my front door in 2 days! This company is fantastic!!!! Read more