Cooktop Parts

• Gas smell
• Won't start

I replaced the burner head. I turned off power to the stove, although I did not turn off the gas. I gave the old burner head a slight twist counter-clockwise until it lifted off the stove. I used the pliers to pull the wires from the old burner, then placed them onto the contacts on the new burner. Set it in place, and gave it a clockwise twist until it was snug. This stove originally came with gaskets beneath the burners, but the info for the replacement part stated that a gasket was not... Read more

I researched on the net, ordered the part, it arrived the next day. Took about 45 minutes to replace. Fairly easy fix. Read more

The glass was easily replaced. Just a few screws to remove cover then remove bad glass then i dropped in the replacement glass then reinstalled cover. Ithen put the door back in the stove. 15 minute job!!! I was so surprised to see how easy it was!!! Thanks! Part fit perfectly!!! Read more

• Element will not heat

Ordered a new terminal block kit from Appliance Parts Pros. Shipping was lightening fast. Slapped the new part on my stove and its never worked better. Thanksgiving was saved! I'd replace the rest of my stove's terminal blocks if they weren't $50 a piece...sheesh! Read more

• Element will not heat

Unplug range. Open oven door to gain access to the cook top lock-down screws, located under the front edge of the cook top. Tip the cook top up and carefully remove it by pulling forward. Set aside in a safe place. Remove old, burned-out, element by removing the single lock tab, located on one of the three mounting posts, then lift up. Leave the wiring attached. Flip the element over and remove the three mounting tabs, making note of their numbered locations. Transfer the mounting tabs to... Read more

Based on internet search and data found on APPLIANCE PARTS PRO, I deduced that the "infinite control " module was most likely bad. Replaced it and all is good. Toughest part was remembering how to disengage cooktop from down draft blower and then pulling the cook top up in within it's opening. Once pulled up, I put short 2x4's across the opening corners to support the cooktop safely while I worked on it. Next issue was figuring out exactly which screws held the glass top in place. As... Read more

New spark module Read more

GE Microwave/Convection Oven. Removed case (carefully). Tested in-line power cord fuse with multi-meter. Fuse was good. Noticed a scorch mark on a wire connected to the oven cavity thermal fuse. The fuse appeared to have been overheated from too much movement in it's mount. Removed part from unit and used number on the part to order a new one. Installed new part, re-assembled, and unit works fine. Read more

After watching a youtube video, I disassembled the front cover on the cooktop (be sure to turn off the power supply). I then switched the potentiometers on two burners. The burner that was not working now worked and the burner that did work did not. Easy to find the culprit....ordered a new potentiometer from here and though I only got regular shipping, it was actually delivered the NEXT DAY! 5 minutes, put in the new part, and all burners work. Great site, thanks for the help! Read more

Replaced switch with a new one. also replaced the 4 knobs Read more

Ordering the right part is the key. This is the element with 3 wire connectors NOT the usual kind with 2 prongs that slide in. Thank goodness this company carries these elements for old GE built-in stoves. I'm not super handy but replaced two in about 40 min. Make sure you save the old ceramic clamps. The three prongs of the element with connected wires need to fit completely in the ceramic grooves so the two sides can be clamped together. The new element comes with everything you need but... Read more

Replaced the switch infin by watching the video Read more

I got a new part and replaced it. Read more

Very easy. Read more

So, you would think that Bosch would make the door handle a TAD more accessible for a quick replacement and repair. You have to first remove the plastic lining on the back of the door, then the black metal surround that holds the inner glass to be able to get to the two screws that hold the door handle supports. It takes some patience as most of these two peices and "snap" in and you just have to carefully see how the two components are held in to remove them without breaking them. So.... 1 -... Read more

Replaced knob. Read more