Dishwasher Dispenser Parts

This replacement lid is the outer cover used to protect internal components and help contain water and debris. It restores a finished appearance and helps the appliance operate without interference from loose or damaged tops. What it does:

• Covers and protects internal components from splashes, dust, and debris
• Helps maintain proper sealing and prevents items from falling into the machine
• Restores the appliance's finished appearance after damage or wear
• Can reduce rattles or interference caused by a cracked or warped lid

• One replacement lid

• Disconnect power and shut off water before servicing
• Handle carefully to avoid chipping or scratching painted surfaces
• Typical installation uses existing fasteners; inspect mounting points and replace hardware if damaged

This latch cover insert replaces a worn or broken door latch trim so the appliance door closes cleanly and looks finished. It restores a secure, aligned latch area and improves door appearance. What it does:

• Covers and protects the door latch mechanism from dirt and damage
• Provides a smooth surface for the door to engage the latch properly
• Helps prevent rattling or misalignment caused by a damaged trim
• Matches the original finish for a factory look

• Remove power to the appliance before beginning any work
• Typically snaps or screws into place; retain original fasteners if present
• Inspect surrounding latch components and replace if damaged

Also order retainer part number WP3400918

The Detergent Dispenser is an OEM part for Frigidaire dishwashers. It dispenses the necessary doses of detergent at precisely timed intervals during cycle operation. 

Causes of dispenser malfunction stem from normal wear over extended use. Mineral buildup can accumulate inside inhibiting proper dispensing action. Mechanical or electronic components controlling release functions are also susceptible to failure.

Symptoms of a bad dispenser include:

• Dishes not getting completely clean after cycles
• Residual food or film left on dishware   
• Error codes related to detergent supply issues
• Leaks or spills from the dispenser area

This OEM Frigidaire part is also compatible with some Electrolux, Gibson, and Kenmore appliance models. 

This dishwasher detergent and rinse aid dispenser stores detergent and releases it at the correct point in the cycle while metering rinse aid. Replacing a worn dispenser restores consistent soap release, cleaning performance, and spot-reducing rinse aid delivery.

• Holds detergent and rinse aid and seals to the inner door
• Opens the detergent cup at the programmed time during the wash
• Meters rinse aid into the final rinse to help reduce spotting
• Typical symptoms: detergent left in cup, dispenser door won't open, rinse aid not dispensing, or leaks around the dispenser area

• Disconnect power to the dishwasher before servicing
• Access from the inner door by removing the perimeter screws to separate the door panels
• Disconnect the wire harness, release the locking tabs, seat the new dispenser evenly, and tighten screws evenly to compress the seal
• Run a short cycle to check for leaks

The Thermostat Housing is an OEM part for Whirlpool dishwashers. It encases the thermostat responsible for accurately monitoring water temperatures throughout cleaning cycles. 

Symptoms of a faulty housing include:

• Inconsistent or improper water heating  
• Delayed or incomplete cycles from temperature control issues
• Error codes or failure detection by the control board

Causes may involve cracks allowing steam penetration, loose mounting points compromising seals, or damaged seals leaking interior thermostat components. 

This OEM replacement fits Whirlpool, KitchenAid, Jenn-Air, and some Kenmore models as well.

This dispenser is the front housing that channels ice and water from the refrigerator to the user, restoring proper dispensing and a finished appearance. It fits into the refrigerator door and works with the dispenser controls. What it does:

• Directs and channels ice and water from the internal supply to the exterior dispenser opening
• Provides the mounting surface and openings for dispenser controls, actuator/lever, and chute
• Helps prevent leaks and misdirected water when the dispenser is working correctly
• Commonly replaced for cracked housing, broken mounting tabs, or cosmetic damage that affects dispensing

• One dispenser housing assembly

• Disconnect power and turn off the water supply before starting any repair
• Handle plastic clips and tabs carefully during removal to avoid breakage
• Reuse any electronic components only if compatible; replace damaged clips or seals
• After installation, turn on water and power and check for proper operation and leaks

The Tank is an OEM part for Whirlpool washing machines. It properly dispenses detergent during the wash cycle.

Causes of a bad detergent tank can include: cracks, holes or other damage that cause leakage or improper detergent dispensing. Scaling or mineral buildup inside the tank over time may also lead to detergent dispensing issues.

Symptoms of a bad detergent tank include:

• Detergent not being fully dispensed or released during the wash
• Residue or leftover detergent remaining in the tank after cycles
• Clothes not getting properly cleaned due to insufficient detergent release

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This cap tower upper is the replacement cover piece for the top of the dispenser/tower assembly. It restores the finished fit and alignment of the tower so the dispenser components sit correctly and look complete. What it does

• Covers and protects the top section of the tower/dispenser assembly to keep internal components shielded.
• Restores the correct appearance and alignment of the dispenser area after damage or wear.
• Helps prevent debris from entering the tower opening and interfering with nearby parts.
• Commonly replaced when cracked, broken, chipped, or missing, or when the tower no longer seats properly.

• One cap tower upper.

• Disconnect power to the appliance before beginning any repair.
• This part typically snaps or fits into the tower; inspect surrounding clips or tabs for damage before installing.
• Handle plastic tabs carefully to avoid further breakage; replace any damaged mounting clips.