Dishwasher Valve

This float switch lever is the actuator that moves the dishwasher's tub float to operate the water-level/flood-sensing switch, helping the appliance detect overfill and control fill/drain cycles. Replaces a worn or broken lever to restore proper float activation. What it does:

• Transfers movement from the tub float to the float switch so the machine senses water level correctly
• Commonly needed when a cracked or detached lever prevents the float from engaging the switch
• Can stop overfill-safety trips or no-fill symptoms caused by a non-responsive float assembly
• Works with the existing float and float switch; restores mechanical linkage function

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove lower access panels or tub components as required to reach the float assembly
• Inspect surrounding clips and the float for damage; replace any broken hardware
• Tighten securely but avoid over-torquing; test float movement and switch activation before reassembly

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser, restoring proper water delivery when the system won't fill or dispense. Direct-fit replacement that helps stop leaks and restore function. What it does:

• Opens and closes to let water into the ice maker and dispenser when signaled
• Stops water flow when the fill cycle or dispense cycle ends
• Common part to replace for slow/no ice production or no water from dispenser
• Replaced when valves leak or water lines fail to pressurize

• Disconnect power and shut off the water supply before starting work
• Verify tubing connections and electrical connector orientation before reassembly
• Inspect supply lines and gaskets; use proper replacement fittings if damaged

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

This water inlet valve controls water flow into the refrigerator for the dispenser and ice maker, restoring reliable filling and ice production. It replaces a worn or failed valve to stop flow issues and intermittent filling problems. What it does:

• Controls and directs incoming water to the ice maker and door dispenser via two solenoids
• Opens and closes to allow timed fills for ice production and dispensing
• Commonly used when the dispenser produces no water or has weak flow
• Can cause the ice maker to stop filling or produce small/partial ice cubes

• Disconnect power and shut off the water supply before servicing
• Inspect and tighten water line fittings; check for leaks after reconnecting water

This inlet valve controls the flow of water into the appliance, restoring proper fill and water delivery when the original valve leaks, fails to open, or allows continuous filling. A direct-fit replacement when the valve assembly is damaged. What it does:

• Opens and closes to allow water into the appliance during cycle fill
• Stops water flow when the fill is complete to prevent overfilling
• Commonly replaced for symptoms like no water fill, slow fills, or constant leaking/overflow
• Works with factory water lines and electrical connectors to regulate supply

• One inlet valve assembly

• Disconnect power and shut off the water supply before starting
• Handle valve and solenoids carefully; avoid damaging electrical terminals or inlet fittings
• Verify proper hose and electrical connections and test for leaks after installation

This flapper is a small plastic sealing flap that helps control and direct flow inside the appliance, restoring proper sealing and movement where the original flap is worn or broken. Replacing a damaged flapper helps stop leaks and restore normal dispensing or airflow. What it does

• Acts as a sealing flap to open and close a flow path or duct, preventing unwanted leaks or air transfer.
• Restores proper movement and alignment so dispenser, damper or valve mechanisms can operate smoothly.
• Worn, cracked or broken flappers can cause leaks, incomplete dispensing, or temperature/airflow problems.
• Simple wear or breakage is the most common reason to replace this part.

• One flapper

• High-level replacement; typically accessible by removing the cover or access panel where the flap is mounted.
• Inspect surrounding clips, pins or mounts for damage and replace if worn to ensure secure fit.
• Disconnect power and, if applicable, water supply before beginning work to avoid injury or leaks.