Duct Parts

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

NOTE: The clamps no longer come with the connector hose. The part number for the clamp is WD01X10322.

The dryer vent close elbow connects and redirects the exhaust ductwork at tight angles, typically located where the vent exits the dryer or building. Replace if you notice reduced airflow, lint buildup, visible damage, or if the connection becomes loose or detached.

This transition duct directs dryer exhaust from the appliance to the home vent, helping maintain proper airflow and reduce vent leaks. It keeps exhaust moving out of the cabinet for safer, more efficient drying. What it does:

• Channels dryer exhaust from the appliance outlet to the household vent
• Helps prevent lint and moisture from escaping into the cabinet or laundry area
• Can reduce long dry times and overheating caused by restricted or damaged ducting
• Commonly replaced when venting is crushed, torn, or leaking

• Disconnect power (and gas, if applicable) and move the appliance away from the wall before replacing the duct
• Inspect adjoining vent hoses and seals; replace or reseal as needed for a tight fit
• Use appropriate clamps or connectors and follow local venting codes for safe exhaust routing

Steam hose kit connects water source to dryer steam system. Includes rubber fill hoses and Y connector. Replace if hoses are cracked or leaking.

This 5-foot flexible aluminum vent hose is a bendable, accordion-style exhaust duct that connects your dryer's exhaust outlet to the wall vent, allowing for easy routing around obstacles in tight laundry spaces. The flexible design lets you position the dryer close to the wall even when the vent connection is not perfectly aligned. Replace this hose if it is crushed, torn, or disconnected, as a damaged hose can cause poor drying performance, excess heat buildup, or a lint fire hazard.

Factory vent hose assembly for dryers. Installs between drum and exhaust port. Replace when hose is cracked, torn, disconnected, or missing.

Adjustable periscope vent for dryers with limited clearance. Installs between dryer exhaust and wall port. Replace if cracked, damaged, or missing.

This is the gas tube assembly that connects the gas valve to the burner assembly inside the dryer. It channels gas from the manifold to the burner where it is ignited to produce heat for drying. Replace this tube if you detect a gas smell near the dryer, notice visible damage or corrosion on the tube, or if the dryer fails to heat properly.

Molded elbow connector that redirects dryer exhaust to your home vent duct. Replace if cracked, loose, or leaking to restore a secure connection.

In-wall periscope vent for dryers installed in tight spaces. Replaces damaged, crushed, or missing periscope vents behind appliances for proper exhaust.

Exterior vent hood for dryer exhaust systems. Replaces cracked, broken, or missing vent covers. Installs at outdoor vent exit point.

8-foot flexible exhaust hose that channels airflow from your dryer to the exterior vent. Replace if torn, kinked, crushed, or clogged with lint buildup.

This duct assembly channels exhaust from the appliance to the home vent, restoring proper airflow and helping reduce lint and moisture buildup. It's a direct-fit replacement for the original ducting on compatible LG units. What it does:

• Directs heated air and moisture from the appliance to the exterior vent
• Replaces damaged, crushed or disconnected ductwork that can restrict airflow
• Helps reduce lint accumulation in the cabinet/vent path when installed and maintained
• Restores a sealed connection between the appliance outlet and household venting

• Disconnect power and unplug the appliance before beginning any repair
• Follow for disassembly and routing; use proper clamps or screws to secure connections
• Inspect connected gaskets, clamps and the external vent path; replace or clean as needed
• Do not operate the appliance with obstructed or damaged venting; clean lint regularly to reduce fire risk