Need Help?
Call or text
The Dryer Seal is an OEM replacment part for Frigidaire dryers. It is located at the doorway opening where the drum rotates and helps prevent lint, moisture, and heat from escaping. The seal is a crucial component that ensures efficient drying and heat retention within the dryer drum.
Causes of a bad seal can include wear and tear over time from continuous use or damage due to mishandling. The nylon seal experiences a lot of friction and heat stress with each drying cycle.
Symptoms of a bad seal include:
This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more
Upper felt seal creates a tight barrier between drum and cabinet to prevent clothes from catching in gaps. Replace if fabric snags or grinding noises occur.
My 12 year old Frigidaire stack on top dryer had been beeping distress messages in some unintelligible code for about a year when it completely stopped producing heat. It also had a long standing issue with delicate fabrics and thin straps or drawstrings getting caught in the drum. After using this site to troubleshoot and viewing the useful how-to videos, I ordered and replaced the heating element, thermal limiter, and felt seals. Based on others' stories, I decided to also replace the rear... Read more
Freezer door gasket seals the door to prevent warm air entry and cold air loss. Replace if torn, cracked, or not sealing properly. Confirm fit by model.
Gasket and liner arrived as planned. Clips were a day later. Used "hog ring" pliers to remove the clips, worked great. Pre-punched holes in the gasket did not match the original but the plastic liner did. Used an ice pick to punch the gasket and inserted the clips. This is a chest freezer, so install the hinge side first. Read more
Ice buildup in fresh food section or around evaporator? This air handler housing kit stops warm-air leaks that cause frost and temperature swings. 30-min repair.
I removed the fresh food ice maker found the drain tube for ice maker frozen. This was causing the back of the unit to rust out. This also caused the water to run down the back of the unit the into the duct work and into the freezer causing ice buildup. I then defrosted the freezer removed the rear duct work and the freezer drain pan cover. I found the freezer drain was not draining. I removed the exterior rear cardboard cover and located the freezer drain tube removed it and found that it was... Read more
Replace your electric range oven door seal when compressed, frayed, or heat escapes. Maintains temperature for efficient cooking. Verify fit by model.
Removing was easy. Pull out the ends of the seal, the ends aren't locked in. Then, pull up on each retaining clip. Each clip is held in with spring tension. Reinstallation was easy too. Start on one end, Twist frayed end into cone-like shape and insert into one of the holes for the seal. Push in with a skewer/screwdriver. Insert first clip into the first hole. Go around in a linear fashion, inserting each clip into each hole. After the last clip is pushed in, twist the end of the frayed end... Read more
Forms a watertight seal around your dishwasher door to prevent leaks during wash cycles. Replace if cracked, worn, or causing water leakage. Confirm fit by model number before ordering.
Ordered a new seal and the install was fairly easy. Read more
Replace your worn freezer door gasket to restore an airtight seal, prevent cold air loss, and reduce frost buildup. Confirm fit by model number.
Loosened the top half screws, pulled the old seal out, put new seal in, snugged top screws, repeated process for the bottom. Went well, no problems. Read more
Seals the fresh food compartment door to prevent air leaks and maintain temperature. Replace if torn, loose, or causing condensation. Confirm fit.
Replace the gasket, very simple Read more
Prevents leaks and seals your washer door during wash cycles. Replace if torn, moldy, or causing water leakage. Verify fit with your model number.
I replaced the door boot with a new one from AppliancePartsPros.com. The most difficult part was starting at the back end of the new boot onto the stationary rim, just in front of the tub. And then anchoring it in place with the existing spring from the previous boot. To start the boot I had to hook the top edge of the boot, where the arrow tab is, onto the rectangular projection on the tub rim and then roll the rubber boot edge down around the tub rim and hope the rim was going into the... Read more
Replace your range oven door gasket to prevent heat escape and maintain proper temperature. Snaps into place with embedded clips. Confirm fit by model.
Easy just pull clip and put back Read more
Replace your freezer door gasket to restore a tight seal and prevent air leaks. Fixes frost buildup and energy loss. Confirm fit with your model number.
Ordered the parts from this parts site and the wife and I replaced both. Working great! Read more
Dishwasher door seal prevents leaks by creating a watertight barrier around the door. Replace if you notice water pooling or leaking. Verify fit with your model.
Replace your dryer door gasket to restore an airtight seal and prevent heat loss. Installs in minutes—just pull out the old, snap in the new. Confirm fit.
The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more
Seals washer tub halves to prevent leaks between drum sections. Replace if leaking onto floor or between shell halves. Confirm fit with model number.
Separated shell and replace oring. Replaced springs and shocks. Read more
This freezer door gasket seals the door perimeter to prevent air leaks and maintain proper temperatures. Replace when worn to reduce frost buildup and improve efficiency. Verify fit with your model number.
Watched a You Tube video on how to do it. Read more
Washer door boot seal creates a watertight barrier between door and drum. Replace if torn, moldy, or leaking during cycles. Verify fit with your model.
Replaced with new bellows from appliance parts pros. Read more