Electrolux Valve

Water leaking into the tub or not filling properly? This inlet valve controls water flow into your laundry center. Moderate DIY repair—about 1 hour.

Burner won't light or knob won't turn? This top burner valve controls gas flow to restore reliable ignition and flame control. DIY-friendly replacement.

This drain valve controls the flow of water out of the appliance to remove standing water and prevent overflow. Replacing a faulty valve restores normal draining and helps stop pooling or persistent drain error symptoms. What it does:

• Opens and closes to release water from the appliance drain path.
• Works with the pump/drain line to move water out during cycles.
• Common issues indicating failure: appliance won't drain, water pooling, or intermittent drain errors.
• Fits as the direct replacement component for the OEM valve in affected models.

• Disconnect power and turn off the water supply before starting work.
• Expect residual water in hoses; have towels and a pan ready to catch spills.
• Remove and replace using basic hand tools; keep clamps and seals secure to avoid leaks.

This safety valve controls gas flow to the oven burner. When signaled by the igniter, it opens to allow ignition and helps maintain consistent heat, supporting safe, reliable preheating and baking performance.

• Regulates gas flow to the oven burner under control of the igniter and thermostat/electronic control
• Prevents gas from flowing until proper ignition conditions are met
• Common symptoms: oven won't ignite or heat, intermittent heating, extended preheat time, or weak/unstable flame
• Often inspected when the igniter glows but the burner does not light

• Disconnect power and shut off the gas supply before servicing
• Transfer any model-specific fittings or brackets from the original valve
• Use approved thread sealant on threaded connections; support tubing and avoid overtightening
• After installation, leak-check every connection with a soap-and-water or leak-detection solution

Fix I10, I20, or I30 error codes and slow water filling with this dishwasher water inlet valve. Stops mid-cycle failures and prevents leaks. DIY install.

Fixes oven not heating or slow to heat issues. Controls gas flow to burner for safe ignition. Common repair for delayed heating or no heat problems.

This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does

• Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
• Seals the water line to prevent drips or continuous flow when the dispenser is idle.
• Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
• Works with the door dispenser plumbing—electrical/connectors remain unchanged.

• Disconnect power and shut off the refrigerator water supply before starting.
• Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
• Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
• Test for leaks and proper dispensing after restoring power and water.

Fix a washer that won't fill or fills slowly with this water inlet valve. Controls hot and cold water flow into the tub. Direct replacement part.

This water inlet valve controls water flow to the refrigerator's ice maker and water dispenser, restoring normal dispensing and ice production when the valve is faulty or leaking. What it does

• Opens and closes to allow water into the ice maker and dispenser as commanded by the refrigerator.
• Stops water flow to prevent overfilling; a failed valve can cause no water, slow flow, or continuous filling.
• Commonly linked to symptoms such as no ice production, weak or no water from the dispenser, or visible leaks at the valve.

• One water inlet valve assembly.

• Disconnect power and shut off the water supply before starting work.
• Relieve line pressure and have towels ready for residual water when disconnecting fittings.
• Inspect and replace any worn water line fittings or gaskets; tighten connections to manufacturer torque—do not overtighten plastic fittings.

Burner won't light or flame is uneven? This cooktop top burner valve controls gas flow to individual burners. Common fix for flame control issues.

Fix a burner that won't light, won't stay lit, or has uneven flames with this top burner valve. Controls gas flow to individual burners on gas cooktops.

Burner won't ignite or stays on low heat? This top burner valve controls gas flow to individual burners. Moderate DIY repair restores proper flame.

If your cooktop burner won't ignite, won't turn off, or has weak flames, the top burner valve may need replacement. Controls gas flow to burners.

Dishwasher drain check flapper valve prevents backflow and water leaking into the tub. Slides into filter assembly slot. Simple DIY repair.

Gas not flowing to burners or oven not heating? This range safety valve controls gas flow to prevent leaks. Moderately difficult repair for experienced DIYers.