Jenn-Air Parts

If you have a problem of water pressure when you press for water at the dispenser your problem migth be your filter head assembly. Thanks to appliAncepartspros for their assistance Read more

• No heat or not enough heat

The root cause was the front glides. They were virtually gone, and the drum was on metal to metal. So I replaced them with a front glide kit. I also replaced the belt, rear rollers, and lint screen. I am happy to say all the parts fit perfectly, and I couldn't find a better price anywhere else. I will definitely keep you on file for the next time I need appliance parts! Thank you! Sincerely, pw Read more

Well, I gotta say I was happy to find you still had parts for almost 20 year old microwaves. The microwave itself worked fine, so I hated to have to buy a new one, but I just couldn't take being hit in the head anymore; and my fix of using string and wire to tie it to the surrounding cabinets was unsightly to say the least. I'm glad I did some research and found this part - all I had to do was pop it in place and now the vent grill is secure. Problem solved with minimal cost. Read more

Based on internet search and data found on APPLIANCE PARTS PRO, I deduced that the "infinite control " module was most likely bad. Replaced it and all is good. Toughest part was remembering how to disengage cooktop from down draft blower and then pulling the cook top up in within it's opening. Once pulled up, I put short 2x4's across the opening corners to support the cooktop safely while I worked on it. Next issue was figuring out exactly which screws held the glass top in place. As... Read more

Water dispenser came down to a trickle and made a lot of noise, I changed the filter but it didnt help and thus the water tank/head assembly needed to be replaced. Replacing the water Tank/head assembly was an easy task, the hardest part is removing the covers and taking care of not breaking the insulation of the water inlet hose. For the not-so-experts like me it is also good to rememebr to have a bucket to collect all the water that comes out after the connection to the solenoid valves is... Read more

Dishes were 'gritty' with an almost invisible coating of specks smaller than grains of salt. Prior to ordering parts, I had to determine which part(s) needed replaced and which could benefit from a good cleaning. After viewing Appliance Parts Pros YouTube Videos, I removed the Main Manifold (snaps right off) including the Top Spray Arm. I discovered the Flappers of the Docking Station (AP6009888) were worn out and/or missing. I removed the Docking Station simply by popping the old one off... Read more

Replaced the old housing with new water filter housing. Read more

The video was very helpful, but my KitchenAid model required slightly more steps. Only the two screws in front held the filter housing, same as the video shows, but it has to be removed from the rear. My model did not have the wire brace, only the two front screws held the housing. Shut the water off and pull the electrical plug. Remove the two screws holding the filter housing in the front. Remove the lower panel in the rear at the bottom of the refrigerator. Remove the two screws holding the... Read more

Ordered a new one Read more

Replaced housing. That was simple but finding directions in how it I remove top of cabinet was time consuming. After two hours of searching I finally found one article that explained why there were no screws to remove. Read more

I was just replacing my filter,on my vent. Read more

It's bit of a chore in that on my Whirlpool Refrig you need to remove the grill on bottom front and the Utility Panel on bottom rear. Then unscrew the original filter housing and pull it out through the back of utility opening. Remove the two water hoses and put them into new filter house. Reverse the disassembly process to reinstall new filter housing. I'm old and slow so the process took me about 45 minutes. (Note: Unplug electric and turn off water inlet before starting.) Read more

• Not cleaning dishes properly

Searched on this site and found likely cause and solution to problem. After watching APP video, I was able to remove dishwasher filter and confirm clogged filter. Ordered the new part and it was shipped quickly. Reinstalled it per video instructions and it worked perfectly! Thank you APP.com for making me look like an appliance repair expert on this and several other projects. This has saved me lots of money over the last few years, and kept my slightly older appliances in working order and... Read more

I ordered a new grease filter. There was no fixing it. Read more

Went on internet, found a great site and learned that the cold water hose filter was very much clogged at the machine intake. Cleaned it and voila. Ordered an extra filter from Appliance Pros.com and literally was amazed that it arrive within 2 days of my internet order. Great efficiency and customer service….great experience. Will definitely use them in the future….thank you! Read more

Ordered what was shown on the pc. I removed old ones, put in new ones good to go. Read more