Maytag Heating Element

Ordered part and installed it. Broiler works as advertised. Read more

Your on line video pointed out the problem, how to test, and how to replace the element. I ordered the part it came the next day. Wife is very happy. Read more

• Little to no heat when baking
• Oven not heating evenly

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Using YouTube, we learned how to dismantle the dryer and replace the part properly. Read more

Ordered new one from you, unscrewed and unplugged the old one, plugged in the new one Read more

Range has no model ID plate anywhere. Flip off electric at circuit breaker box. Opened top of range and noted details of the faulty burner, including confirm that outer coil was fried. The maker info on back of element was useless in finding replacement: more useful was general shape, and the numbers around edge on back. Close up range, since low heat element still working. Turns out all Maytag double oven Gemini ranges use the same hi-low element, but double check appearance just in... Read more

• Element will not heat

I ordered 2 bake elements and bulbs and was able to easily fix 1 of the ovens. The serviceman who repaired the left oven did not repair it correctly so, one of the wires was not accessible so, I could only fix one oven. After shutting off the power, I EASILY fixed the right oven - with a LOT of care and a little elbow grease - in disconnecting the broken element, by doing exactly as it said to in the video, making certain not to allow the wires to slip back into the hole that it was pulled... Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

Replaced it with a new element. Fairly easy to replace if you have any kind of mechanical know how. Ordered the part for a 2 day delivery and got it the next day. Read more

• Too hot
• tripping breaker

I found the assembly with heater element, thermostat, and the thermal fuse already assembled (cheaper than finding what part was bad and ordering that one part). unplugged dryer, pulled it out and removed the dryer exhaust tube, the top and front. The harness was a little short so I wasnt able to pull the whole heater assembly out before disconnecting. BEFORE disconnecting I took a picture so that if my brain forgot what wires went were!!!! put the dryer back together and put a load that just... Read more

It was very easy caled up ordered the part no prblem got it in 3 days.Got a phillips screw driver removed the top of the stove took out the old one a put in the new one had it fixed within minutes very easy diy no need to pay someone alot of money for this easy fix. Read more

• Element will not heat
• Little to no heat when baking
• Oven not heating evenly

Removed 2 sheet metal screw pulled element out about 2 inches. Removed two Spade connections. Removed the element from the oven. Inserted the new element into the over, connected the two spade connector. Reinstalled the two sheet metal screws. Set the oven to bake for testing and tested until the element turned red. Total time less than 5 minutes. Read more

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

• Element will not heat

Purchased a new Element surface and installed same... All Okay now... Read more

Replaced the heating element and we have heat to dry our cloths THANKS Read more