Maytag Heating Element

This genuine heating element restores consistent, controlled heat so your appliance can reach and maintain the proper temperature. Replacing a failed element can resolve no-heat or weak-heat issues and bring performance back to normal.

• Converts electrical energy into heat when powered by the control
• Helps the unit achieve and hold the set temperature during operation
• Typical failure symptoms: no heat, slow or uneven heating, cycles that take longer than normal, visible damage to the element
• May trigger heat-related error codes when failing

• Disconnect power at the breaker or unplug the appliance before servicing; allow all components to cool completely
• Note wire locations and terminal orientation before removal; transfer any mounting hardware from the original if needed
• Avoid bending or striking the element; handle by the bracket/insulators
• After installation, run a test cycle to check for secure connections

Built for electric dryers that require a 240V heater, this complete heater assembly restores proper heat output. Replace a burned-out element to resolve no-heat or weak-heat complaints and return your dryer to consistent, efficient drying.

• Generates the hot air needed to dry laundry during the cycle
• Typical failure symptoms: drum turns but no heat, longer dry times, or intermittent heating
• Can be checked with a continuity test; a broken or grounded coil indicates replacement is needed
• Factory-style 240V configuration for proper operation on compatible models

• Disconnect power at the breaker before servicing
• Access the heater per your model's service procedure and document wire locations
• Move wires to matching terminals; transfer any attached brackets/sensors from the old assembly if your model uses them
• Clear lint and verify airflow before a test run to confirm proper heating and cycling

Restore consistent bottom heat in your oven with this bake element. When the original element burns out, the oven may not heat, preheat slowly, or bake unevenly—replacing it restores dependable baking performance and even results. What it does:

• Supplies heat from the bottom of the oven during Bake cycles
• Helps the oven reach and maintain the set temperature
• Common symptoms of failure: little or no heat in Bake, slow preheating, uneven baking/browning
• Visible signs can include blisters, cracks, or breaks in the element

• 1 bake element

• Disconnect power at the breaker and allow the oven to cool before service
• Remove mounting screws and carefully pull the element forward to access the wires
• Transfer the two wires to the new element, keeping them from slipping back into the oven cavity
• Reinstall mounting screws, restore power, and test Bake operation

• A healthy bake element typically shows continuity on a multimeter; an open reading indicates it has failed.

Restore proper top heat to your oven with this broil element. It delivers the intense, even radiant heat needed for broiling, so foods brown and sear correctly when the original element fails or is damaged.

• Supplies high, direct heat from the top of the oven during Broil
• Common fix for no-broil or weak broiling performance
• Replace if the element is blistered, cracked, warped, or shows arcing
• Help resolve uneven browning or a tripped breaker caused by a shorted element

• Disconnect power at the breaker before servicing
• Remove oven racks; unfasten the element's mounting screws and gently pull it forward
• Support and disconnect the wires; attach them to the new element and position it
• Secure the element, ensure connections are tight and clear of metal, then restore power and test

This surface heating element restores reliable heat to an electric range or cooktop's top burner. Replace a failed or damaged element to bring back even, responsive heating for everyday cooking. What it does:

• Supplies heat to the selected surface burner when the control is turned on
• Can correct no-heat, weak or intermittent heat, or overheating due to internal failure
• Replaces elements with visible damage such as breaks, burn marks, or hot spots
• Helps restore consistent temperature control across the cooking zone

• 1 surface heating element

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element per your model; note wire locations and any brackets before removal
• Transfer wires and any retaining hardware to the new element in the same positions
• Avoid stressing the element or insulation; ensure it sits level and clear of glass/trim before reassembly

This is a radiant surface heating element for smooth-top electric ranges. It replaces a failed burner to restore up to 1300 watts of even heat and dependable temperature control under the glass-ceramic cooktop. What it does:

• Generates radiant heat beneath the glass surface when powered by the burner control
• Restores proper heating if a burner will not heat, heats unevenly, or cycles off too quickly
• Helps eliminate long heat-up times caused by a weakened or open element
• Replaces elements with visible damage such as broken ribbons, burn spots, or charred terminals

• 1 radiant surface element (1300W)

• Disconnect power at the breaker or unplug the range before servicing
• Allow the cooktop to cool fully; lift/prop the glass top to access the element
• Note wire positions; transfer any mounting brackets/clips from the old element and reconnect wires securely
• Handle the element carefully and avoid stressing the ribbon; reassemble and test the burner before finalizing

This bake element is the lower-oven heating source that brings your range or wall oven up to temperature for consistent baking. Replace a burned or damaged element to restore reliable preheat and even cooking results. What it does:

• Provides bottom heat during bake cycles for even, consistent cooking
• Primary heat source for preheating and maintaining set temperature
• Common symptoms: no heat in bake, slow preheat, won't reach temperature, uneven baking, visible blisters/breaks on the element
• Useful clue: broil works but bake does not

• 1 bake element

• Disconnect power at the breaker before servicing
• Remove racks; take out element mounting screws; pull element forward to access terminals
• Transfer wires one at a time and ensure tight, insulated connections; don't let wires retract into the cavity
• After reassembly, run a brief bake test to verify operation and clear any residual smoke from first heat-up

Restore a reliable burner with this replacement surface element. It provides the heat your cookware needs so meals warm efficiently and evenly when the control is turned on, replacing a worn or failed top burner element. What it does:

• Heats the selected cooking zone when its control is engaged
• Replaces a failed, shorted, or physically damaged element
• Helps resolve issues like a burner not heating, heating only partially, or heating inconsistently
• Supports even cooking performance across the cooking surface

• 1 surface element

• Disconnect power at the breaker or unplug the appliance; allow all components to cool
• Access the element; support the cooktop surface if lifted
• Move wires to the new element one at a time to maintain correct connections; reuse existing brackets as needed
• Handle the element carefully; avoid touching heating surfaces and verify secure connections before reassembly and testing

This convection element supplies heat for your oven's convection mode. Working with the convection fan, it circulates hot air to maintain even, consistent baking and roasting performance.

• Provides the heat source during convection cycles for circulated-air cooking
• Helps maintain uniform cavity temperature and even browning
• Restores convection function when the original element is open or damaged
• Common symptoms: convection not heating, fan runs but little/no heat, longer or uneven cook times in convection

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks and the rear interior cover to access the element
• Remove mounting screws, pull the element forward, and transfer wires one at a time; ensure tight, secure connections
• Reinstall the cover, restore power, and run a brief convection test

This replacement heating element restores proper heat in electric dryers designed with two-level heat. It generates the controlled heat needed for both high and low temperature cycles, helping return normal drying performance.

• Heats the air passing through the drum during drying cycles
• Supports two-level heat so high and low temperature settings work correctly
• Typical symptoms include: no heat, insufficient heat, longer-than-normal dry times, or only one heat setting working
• A visibly broken coil or an open reading on a continuity test indicates failure

• Disconnect power before servicing; dryer circuits carry high voltage
• Handle the element carefully—coils and insulators are fragile; do not stretch or deform the coil
• Note wire locations and ensure tight, clean connections during reassembly
• Clear lint and verify airflow; restricted ventilation or failed thermostats/cutoffs can lead to repeat element failure

This 240-volt heater assembly restores the appliance's ability to generate and maintain heat during operation, helping cycles reach designed temperatures for proper performance and results. What it does:

• Converts electrical energy into heat for the appliance's heating circuit
• Helps the unit reach and hold target temperatures during heat-required portions of the cycle
• Replaces a damaged, shorted, or open heating element
• Symptoms can include no heat when expected, longer-than-normal cycles, tripped breakers, or heater-related error codes

• 1 heater assembly

• Disconnect power at the breaker before servicing; 240V circuits can be hazardous
• Document wire locations and move connectors one at a time to the new assembly
• Avoid bending or striking the element; ensure secure mounting and proper clearances
• After installation, check related safety devices (high-limit, thermostats, fuses) and verify the circuit has correct voltage and continuity

This part is a grill element that is used on a cooktop. The element is responsible for supplying heat to the cooking area of the cooktop. If the element is not lighting up orange or red when it is turned on, it will need to be replaced. This part may need to be replaced over time due to normal wear and tear on the appliance. Some users may also notice that the element is not heating evenly or works intermittently. If this is the case, this is a genuine OEM replacement part that is made out of high-quality materials. Unplug the range from the electrical outlet and allow the cooktop ample time to cool down before trying to replace it. Wear work gloves for safety during this process.This part is compatible with cooktops that are manufactured by Jenn-Air and Maytag. It is sold individually and comes from the manufacturer.

This broil element provides the intense top heat your oven uses for broiling. Replace a failed or damaged element to restore consistent broiler performance and proper browning when broiling meats and other foods.

• Supplies high, direct radiant heat from the top of the oven during broil cycles
• Restores proper broiling performance for browning and searing
• Replaces elements with open circuits, blisters, cracks, or shorts
• Common symptoms include: broiler won't heat, weak or uneven broiling, visible damage, or the breaker trips when broil is turned on

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely
• Remove mounting screws, gently pull the element forward, and disconnect wires; support wires so they don't slip back into the rear cavity
• Attach wires to the new element and secure with existing screws; avoid bending the element or overtightening
• Restore power and test the broil function

This radiant surface element uses a ribbon-style heater to provide even heat beneath a glass-ceramic cooktop. Replace a failing burner to restore consistent, reliable heating on the affected cooking zone.

• Provides radiant heat to one surface burner zone beneath the glass top
• Works with the surface control to regulate cooking temperature
• Common fix for a burner that won't heat, heats unevenly, or takes too long to heat
• Replace if the element shows an open circuit when tested for continuity

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the cooktop to cool completely; support the glass top per service instructions to access the element
• Transfer wires from the old element to the new one position-by-position; secure using existing brackets
• Avoid touching the element surface; test operation before reassembly

This surface heating element restores reliable heat to one burner on your electric range or cooktop. Replace a failed element to bring back consistent, controllable cooking performance and eliminate cold spots on the affected cooking zone.

• Supplies heat for a single surface burner on an electric range/cooktop
• Replaces a burned-out, shorted, or damaged element
• Common symptoms: no heat, uneven or intermittent heating, slow to heat, or visible damage/discoloration on the element
• Helps return proper response to the surface temperature control

• Disconnect power at the breaker before servicing; allow the cooktop to cool completely
• Access the element per your model's service manual; support the cooktop and handle components carefully
• Move wires over one at a time to the new element to avoid miswiring; secure mounting as originally installed
• Inspect wiring and terminals for heat damage; repair or replace any compromised connectors before reassembly

This 8-inch surface burner element delivers heat on an electric cooktop or range. Replacing a worn or open element restores even heating on the burner zone and reliable response to temperature settings.

• Heats the 8-inch cooking zone when the surface control is turned on
• Helps maintain consistent pan temperature for boiling, simmering, and frying
• Common symptoms: burner won't heat, heats unevenly or intermittently, visible blistering/breaks in the coil, or scorch marks at the terminals
• Replacing a damaged element can prevent further damage to the receptacle/terminal block

• Disconnect power at the breaker and allow the unit to cool completely
• Handle the element by the bracket; avoid bending the coil
• For plug-in setups, pull the old element straight out and firmly seat the new one; for wired connections, move wires one at a time to the matching terminals and secure properly
• Inspect the receptacle/terminal block and wiring; replace if burnt or loose before restoring power