Maytag Spring Parts

Purchased door springs from Appliance Parts pros.com, installed them and door on our Dishwasher was back to normal, Had to pull out dishwasher from under cupboard to get to springs, as they were on the sides of the dishwasher. Read more

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

Replaced with thrust bearing kit. Watched your video and it took about 10 minutes to fix. Thanks Read more

Checked switch with a voltmeter, determined the switch was bad. Ordered a new switch....watched a short how to you-tube video.....and from there.....it was fixed. Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

I replaced drum rollers, axle shafts and front bearing kit. Still had noise. Ordered Idler Arm, Belt Tension Pulley & Washers. I ordered parts at 3:30 pm on a Wednesday, received new parts at 11:30 am Thursday. The instructions & videos were very simple to follow and provided excellent tips. Back up and running with silence in an 1/2 hour. My 13 year old dryer is running like new again. Way cheaper than calling a repairman. Read more

A shout out to A.P.P.: Quality parts always come quickly and are what I ordered. No, they are not always the cheapest nor do they have all parts for everything (who does?) but their website is the easiest to use and cost differences are usually slight. I have found A.P.P. trustworthy and reliable for the ten or so purchases I've made. This repair process requires that the DW be completely free from cabinet sidewalls. For me that meant pulling the DW from its installed undercounter space. I... Read more

First remove the back from the washing machine. Top of the machine came off simple. To replace springs, I took a crow bar but it on the right side underneath where one of the springs should be. Lift the tumbler up remove and replace the spring. Did the same thing to the other side. On the tumbling unit there are spaces for three shock absorbers. Mine only had one shock in the middle. I put two new springs, one in the front and one in the rear. Then I replaced the right side spring with two new... Read more

Without knowing exactly what broke I ordered 2 springs and 2 door spring links. I knew the door springs were weak and a parts man told me many years ago to always replace BOTH springs or the one you didn't replace will soon break. It is a simple procedure, just remember how the springs/links are attached. make a simple drawing or take a picture should you need it. I watched two "how to" video's which made it look harder to do than it really is. Turn the circuit breaker off and turn the... Read more

Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable... Read more

I ordered a pair of springs from AppliancePartsPros.com. When the new springs arrived, I unscrewed the frame from the counter top, slid the dishwasher out part of the way and installed the new springs and saved myself at least one-hundred dollars. Read more

Replaced the door spring. The spring was a perfect fit. Read more

• Door won't close

It was a simple fix. I removed the six screws holding the side panel on the range. Removed the broken parks of the spring. I use a screwdriver to help stretch the new spring into place. I then replaced the side panel and screwed it on. About ten minutes work. Read more