Screws, Nuts, Washers

Size: 8 - 18 ab.

Truss head screw (#10-32 x 3/4) secures panels, brackets, and trim on freezers and refrigerators. Replace missing or stripped screws to restore stability.

Hex washer head screw for refrigerators, freezers, and other appliances. Replaces lost, stripped, or damaged screws during repairs or panel assembly.

Replacement 8-18 x 9/16 machine screw for securing panels, brackets, and internal components. Needed when fasteners are stripped, missing, or worn.

This plug-in SCR is a solid-state replacement that controls electrical power to appliance circuits, restoring reliable on/off control and helping eliminate intermittent operation. It's a direct-fit replacement when the original SCR fails. What it does

• Regulates current flow in the control circuit to switch power to motors or heating loads.
• Stops erratic cycling or loss of power caused by a failed control semiconductor.
• Helps restore consistent operation when an appliance has intermittent start, no heat, or no motor run.
• Provides a rugged, compact replacement with a 5/16" connection style.

• One plug-in SCR

• Disconnect power to the appliance before accessing or replacing the SCR.
• Remove the appliance's control or access panel to reach the control board; note wire locations before unplugging.
• Plug the new SCR into the original connector or replace per the service manual.
• Verify correct operation after installation and reassemble all panels before restoring power.

Secures brackets, panels, and components inside your refrigerator. Replace stripped, rusted, or missing hardware to restore tight alignment and stability.

Flat head sheet metal screw for refrigerators. Secures panels, trim, and brackets with a flush finish. Replace if missing, stripped, or corroded.

Replacement mounting nut for securing internal oven and range components. Needed when original fastener is stripped, missing, or damaged during repair work.

Secures the motor housing to its mounting bracket in washers and laundry centers. Replace if screw is missing, stripped, or damaged during service.

Hex washer head screw secures panels, brackets, and drum assemblies in washers. Replace rusted, stripped, or missing screws to prevent rattling.

This replacement screw fastens panels, brackets, and internal components so assemblies stay aligned and tight during operation. With an 8-18 thread and 0.711-inch length, it matches the original hardware for a precise, reliable hold.

• Secures panels, brackets, and internal components to the cabinet/frame
• Replaces missing, stripped, or corroded screws
• Helps reduce vibration, rattling, and gaps from loose hardware
• Restores proper alignment after service or transport

• Disconnect power and shut off water/gas before servicing.
• Support panels/components while removing and installing the screw.
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten.

Plastic dispenser mounting screw for dishwashers. Secures detergent dispenser assembly to door. Replace if stripped, cracked, or missing.

Mounting screw secures panels, brackets, and interior components in your refrigerator. Replace stripped, missing, or damaged fasteners to prevent rattling.

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

Replacement screw that secures panels, trim pieces, and mounting brackets on cooktops and ranges. Needed when screws are missing, stripped, or damaged.

Factory mounting screw secures panels, brackets, and internal components in microwaves. Replace missing, stripped, or corroded screws to keep assemblies tight.